SH7144 Group FP-112B
User System Interface Board
HS7144ECH61H User’s Manual
Renesas Microcomputer Development Environment System
SuperHTM Family/SH7144 Series
Rev.4.00
2004.1.29
IMPORTANT INFORMATION
READ FIRST
• READ this user's manual before using this user system interface cable.
• KEEP the user's manual handy for future reference.
Do not attempt to use the user system interface cable until you fully understand its
mechanism.
User System Interface Cable:
Throughout this document, the term "user system interface cable" shall be defined as the
following product produced only by Renesas Technology Corp. excluding all subsidiary products.
•
User system interface cable (HS7144ECH61H)
The user system or a host computer is not included in this definition.
Purpose of the User System Interface Cable:
This user system interface cable is for connecting the evaluation chip board and user system.
This user system interface cable must only be used for the above purpose.
Improvement Policy:
Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as
Renesas) pursues a policy of continuing improvement in design, performance, functions, and
safety of the user system interface cable. Renesas reserves the right to change, wholly or partially,
the specifications, design, user's manual, and other documentation at any time without notice.
Target User of the User System Interface Cable:
This user system interface cable should only be used by those who have carefully read and
thoroughly understood the information and restrictions contained in the user's manual. Do not
attempt to use the user system interface cable until you fully understand its mechanism.
It is highly recommended that first-time users be instructed by users that are well versed in the
operation of the user system interface cable.
I
LIMITED WARRANTY
Renesas warrants its user system interface cables to be manufactured
in accordance with published specifications and free from defects in
material and/or workmanship. Renesas will repair or replace any
user system interface cables determined to be defective in material
and/or workmanship. User system interface cables are wearing parts
which Renesas will not repair or replace if damaged and/or worn
through use. The foregoing shall constitute the sole remedy for any
breach of Renesas’ warranty. This warranty extends only to you, the
original Purchaser. It is not transferable to anyone who subsequently
purchases the user system interface cable from you. Renesas is not
liable for any claim made by a third party or made by you for a third
party.
DISCLAIMER
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE
USER SYSTEM INTERFACE CABLE, THE USE OF ANY USER
SYSTEM INTERFACE CABLE, OR ITS DOCUMENTATION,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS
WARRANTY, THIS USER SYSTEM INTERFACE CABLE IS SOLD
"AS IS ", AND YOU MUST ASSUME ALL RISK FOR THE USE
AND RESULTS OBTAINED FROM THE USER SYSTEM
INTERFACE CABLE.
II
State Law:
Some states do not allow the exclusion or limitation of implied warranties or liability for
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which may vary from
state to state.
The Warranty is Void in the Following Cases:
Renesas shall have no liability or legal responsibility for any problems caused by misuse,
abuse, misapplication, neglect, improper handling, installation, repair or modifications of the user
system interface cable without Renesas’ prior written consent or any problems caused by the user
system.
All Rights Reserved:
This user's manual and user system interface cable are copyrighted and all rights are reserved
by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any
form, in hard-copy or machine-readable form, by any means available without Renesas’ prior
written consent.
Other Important Things to Keep in Mind:
1. Circuitry and other examples described herein are meant merely to indicate the characteristics
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for
any intellectual property claims or other problems that may result from applications based on
the examples described herein.
2. No license is granted by implication or otherwise under any patents or other rights of any third
party or Renesas.
Figures:
Some figures in this user's manual may show items different from your actual system.
Limited Anticipation of Danger:
Renesas cannot anticipate every possible circumstance that might involve a potential hazard.
The warnings in this user's manual and on the user system interface cable are therefore not all
inclusive. Therefore, you must use the user system interface cable safely at your own risk.
III
SAFETY PAGE
READ FIRST
• READ this user's manual before using this user system interface cable.
• KEEP the user's manual handy for future reference.
Do not attempt to use the user system interface cable until you fully understand its
mechanism.
DEFINITION OF SIGNAL WORDS
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
CAUTION
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE
emphasizes essential information.
IV
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Do not repair or remodel the emulator product by
yourself for electric shock prevention and quality
assurance.
2. Always switch OFF the E6000H emulator and user system
before connecting or disconnecting any CABLES or
PARTS.
3. Always before connecting any CABLES, make sure that
pin 1 on both sides are correctly aligned.
V
Preface
The HS7144ECH61H is a user system interface board that connects a user system for the SH7144
FP-112B package to the SH7046 E6000H emulator (HS7046EPH60H).
i
Contents
Section 1 Configuration.....................................................................................1
Section 2 Environmental Conditions.................................................................3
2.1 Setting Operating Voltage and Operating Frequency .......................................................3
Section 3 Product Specifications.......................................................................4
Drop in Vcc Level Detection Function:............................................................................4
Section 4 User Interface Specifications.............................................................5
4.1 User System Interface Circuit...........................................................................................5
Section 5 Connection Procedures......................................................................7
5.1 Connecting User System Interface Board to User System ................................................7
5.1.1 Installing IC Socket..............................................................................................7
5.1.2 Installing Cable Head...........................................................................................8
5.1.3 Fastening Cable Head ..........................................................................................8
5.2 Connecting User System Interface Board to EV-Chip Board ...........................................10
5.3 Recommended Dimensions for User System Mount Pad (Footprint) ...............................12
5.4 Dimensions for EV-Chip Board and User System Interface Board...................................13
5.5 Resulting Dimensions after Connecting User System Interface Board .............................14
Section 6 Installing the MCU to the User System.............................................15
Section 7 Verifying Operation...........................................................................17
Section 8 Notice.................................................................................................19
ii
Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for
the FP-112B package. Please make sure you have all of these components when unpacking.
EV-chip board
Screws (M2.0 x 8 mm)
with flat washers
Screws (M2.0 x 12 mm)
with flat washers
Board
Socket cover
Spacer
IC socket
User system
Figure 1 User System Interface Board for the SH7144 FP-112B Package
1
CAUTION
Use an IC149-112C15333-0B socket (manufactured by
YAMAICHI ELECTRONICS Co., Ltd.) for the FP-112B package
IC socket on the user system.
Table 1
HS7144ECH61H Components
No. Component
Quantity
Remarks
With two spacers (2.6MP x 6 mm)
1
2
Board
1
1
IC socket
For the FP-112B package (to be mounted on the
user system)
3
4
5
Socket cover
1
4
4
For the FP-112B package (for installing MCU)
For fastening board (with four flat washers)
Screws (M2.0 x 12 mm)
Screws (M2.0 x 8 mm)
For installing an FP-112B-packaged MCU (with
four flat washers)
6
User’s manual
1
User’s manual for HS7144ECH61H (this manual)
2
Section 2 Environmental Conditions
Maintain the conditions in table 2 when using the emulator.
Table 2
Environmental Conditions
Item
Specifications
Temperature
Operating: +10 to +35°C
Storage: -10 to +35°C
Humidity
Vibration
Operating: 35 to 80% RH, no condensation
Storage: 35 to 80% RH, no condensation
Operating: 2.45 m/s max.
Storage: 4.9 m/s max.
Transportation: 14.7 m/s max.
Ambient gases
There must be no corrosive gases present.
2.1
Setting Operating Voltage and Operating Frequency
Connecting the user system interface board to the SH7046 series E6000H emulator enables
emulation to be done using the user system operating voltage (Vcc: 3.0 to 3.6 V) Before
determining the operating voltage and frequency of the user system, confirm the allowable range.
Vcc
(V)
3.6
3.0
0
4.0
50.0 (MHz)
Operating frequency
: Range which can be emulated
Figure 2 Allowable Operating Range
3
Section 3 Product Specifications
The specifications of this product are shown in table 3.
Table 3
Product Specifications
Item
Specifications
SH7144F
Target processor
Package
FP-112B
Function
Level limitation:
This function keeps the output signal from 3-V emulator system equal
to or less than power supply voltage of the user system (Vcc).
User-system operating
conditions
Power supply voltage
Vcc: 3.0 to 3.6 V
A drop in the Vcc level of the user system is detected when the power
supply voltage drops to 2.6 V or less.
Current consumption
Maximum of 100 mA.
Drop in Vcc Level Detection Function:
When the user system interface board is used, a drop is detected as follows:
When the power supply voltage (UVcc) of the user system is 2.6 V or less, the HEW will detect a
Vcc drop. In this case, a sufficient voltage may not be supplied to the user system; ensure that the
specified value of the power supply voltage is supplied.
4
Section 4 User Interface Specifications
The user system interface board incorporates a level conversion circuit supporting a low-voltage
circuit. Accordingly, when connecting the user system to the emulator, pay attention to the signal
delays and the number of FANINs and FANOUTs.
4.1
User System Interface Circuit
The user system interface circuit of the user system interface board is shown below.
(1) NMI and _RES
5Vcc
UVcc
HD151015
VccB VccA
B
A
Emulator
User system
Figure 3 User System Interface Circuit for NMI and _RES
(2) PE15 to PE0, PC15 to PC0, PB9 to PB0, PA15 to PA0, and PD15 to PD0
QSVcc
QS3384
Emulator
User system
Figure 4 User System Interface Circuit for PE15 to PE0, PC15 to PC0, PB9 to PB0,
PA15 to PA0, and PD15 to PD0
5
(3) AVcc and AN7 to AN0
5Vcc
QS3384
AN7 to AN0
Emulator
Vss
User system
AVss
Figure 5 User System Interface Circuit for AVcc and AN7 to AN0
6
Section 5 Connection Procedures
Connecting User System Interface Board to User System
WARNING
5.1
Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are correctly
aligned. Failure to do so will result in a FIRE HAZARD and
will damage the user system and the emulator product or
will result in PERSONAL INJURY. The USER PROGRAM will
be LOST.
To connect the cable head to the user system, follow the instructions below.
5.1.1 Installing IC Socket
Solder the IC socket for an FP-112B package to the user system.
CAUTION
Be sure to completely solder the leads so that the solder
slops gently over the leads and forms solder fillets. (Use
slightly more solder than the MCU.)
7
5.1.2
Installing Cable Head
CAUTION
Check the location of pin 1 before inserting.
Align pin 1 on the IC socket for an FP-112B package on the user system with pin 1 on the user
system interface board, and insert the user system interface board into the IC socket on the user
system, as shown in figure 6.
5.1.3
Fastening Cable Head
CAUTION
1. Use a Phillip-type screwdriver whose head matches the
screw head.
2. The tightening torque must be 0.098 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
3. If the emulator does not operate correctly, cracks might
have occurred in the solder. Check conduction with
a tester and re-solder the IC socket if necessary.
Fasten the user system interface board to the IC socket for an FP-112B package on the user system
with the four screws (M2.0 x 12 mm) provided. Each screw should be tightened a little at a time,
alternating between screws on opposing corners. Take special care, such as manually securing the
IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening
the screws or twisting the components.
8
Screws (M2.0 x 12 mm)
with flat washers
Board
Pin 1
IC socket
(IC149-112C15333-0B manufactured by
YAMAICHI ELECTRONICS Co., Ltd.)
User system
Figure 6 Connecting User System Interface Board to User System
9
5.2
Connecting User System Interface Board to EV-Chip Board
WARNING
Observe the precautions listed below. Failure to do so
will result in a FIRE HAZARD and will damage the user
system and the emulator product or will result in
PERSONAL INJURY. The USER PROGRAM will be
LOST.
1. Always switch OFF the user system and the emulator
product before the USER SYSTEM INTERFACE BOARD
is connected to or removed from any part. Before
connecting, make sure that pin 1 on both sides are
correctly aligned.
2. The user system interface board dedicated to the
emulator must be used.
1. Make sure the user system and emulator are turned off.
2. Align the connectors on the board with those on the EV-chip board according to their numbers
(figure 7).
3. Adjust the height of the spacer attached to the board with the user system.
10
EV-chip board
Connector No.
EV-Chip Board
Connector No.
Board
Connector No.
UCN1
UCN2
UCN1
UCN2
Board
Spacer
User system
Figure 7 Connecting User System Interface Board to EV-Chip Board
11
5.3
Recommended Dimensions for User System Mount Pad (Footprint)
Figure 8 shows the recommended dimensions for the mount pad (footprint) for the user system
with an IC socket for an FP-112B package (IC149-112C15333-0B: manufactured by YAMAICHI
ELECTRONICS Co., Ltd.). Note that the dimensions in figure 8 are somewhat different from
those of the actual chip's mount pad.
Figure 8 Recommended Dimensions for Mount Pad
12
5.4
Dimensions for EV-Chip Board and User System Interface Board
The dimensions for the EV-chip board and the user system interface board are shown in figure 9.
140.0
EV-chip board
100.0
19.5
31.0
33.5
16.0
User system interface board
Unit: mm
Tolerance: ±0.5 mm
Spacer
Figure 9 Dimensions for EV-Chip Board and User System Interface Board
13
5.5
Resulting Dimensions after Connecting User System Interface Board
The resulting dimensions, after connecting the user system interface board to the user system, are
shown in figure 10.
EV-chip board
31.0
IC socket
(IC149-112C15333-0B
manufactured by
YAMAICHI ELECTRONICS Co., Ltd.)
User system
Spacer (φ6.0)
31.0
Unit: mm
Tolerance: ±1.0 mm
Figure 10 Resulting Dimensions after Connecting User System Interface Board
14
Section 6 Installing the MCU to the User System
CAUTION
1. Check the location of pin 1 before inserting.
2. Use a Philips-type screwdriver whose head matches the
screw head.
3. The tightening torque must be 0.098 N•m or less.
If the applied torque cannot be accurately measured,
stop tightening when the force required to turn the screw
becomes significantly greater than that needed when first
tightening. If a screw is tightened too much, the screw
head may break or an IC socket contact error may be
caused by a crack in the IC socket solder.
4. If the MCU does not operate correctly, cracks might have
occurred in the solder. Check conduction with a tester
and re-solder the IC socket if necessary.
Check the location of pin 1 before inserting the MCU into the IC socket on the user system, as
shown in figure 11. After inserting the MCU, fasten the socket cover with the provided four
screws (M2.0 x 8 mm). Take special care, such as manually securing the IC socket soldered area,
to prevent the IC socket from being damaged by overtightening the screws or twisting the
components.
15
Screws (M2.0 x 8 mm)
with flat washers
Socket cover
MCU (SH7144)
Pin 1
IC socket
(IC149-112C15333-0B
manufactured by
YAMAICHI ELECTRONICS Co., Ltd.)
User system
Figure 11 Installing MCU to User System
16
Section 7 Verifying Operation
1. Turn on the emulator according to the procedures described in the SH7046 E6000H Emulator
User's Manual (HS7046EPH60HE).
2. Verify the user system interface cable connections by checking the pin states with the extended
monitor and checking the bus states with the FILL command (emulator command). If an error
is detected, recheck the soldered IC socket and the location of pin 1.
3. The emulator connected to this user system interface board supports three kinds of clock
sources as the MCU clock. For details, refer to the SH7046 E6000H Emulator User's Manual
(HS7046EPH60HE).
To use the emulator internal clock
Select the clock in the emulator by the CLOCK command (emulator command).
To use the external clock on the user system
Supply the external clock from the user system to the emulator by inputting the EXTAL
pin (pin 74) on the user system interface board or connecting the crystal oscillator to the
XTAL (pin 72) and EXTAL pins. For details, refer to section 4, Clock Pulse Generator, in
the SH7144 Series Hardware Manual.
Figure 12 shows the clock oscillator on the user system interface board.
HCU04
HCU04
HCU04
1 M
HCU04 HCU04
HCU04
47
To E6000H
emulator
270
EXTAL XTAL
System clock
Figure 12 Clock Oscillator
17
To use the crystal oscillator mounted on the EV-chip board
Install a crystal oscillator into the crystal oscillator terminals on the EV-chip board.
Enlarged
view
Crystal
oscillator
X1
X2
Crystal oscillator terminals
Evaluation chip
board
Figure 13 Installing the Clock Oscillator
18
Section 8 Notice
1. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly
aligned.
2. Do not apply excessive force to the user system interface board while it is connected to the
user system.
3. The dimensions of the recommended mount pad for the IC socket for this user system
interface board are different from those of the MCU.
4. This user system interface board is specifically designed for the HS7046EPH60H emulator.
Do not use this board with any other emulator.
5. When power is not supplied to the Vcc pin on the user system interface board, the emulator
displays ** VCC DOWN. The emulator will not operate correctly.
6. The P1 short connector is used for testing. Do not remove the inserted jumper pin.
Figure 14 P1 Jumper Socket
19
SH7144 Group FP-112B
User System Interface Board
HS7144ECH61H User's Manual
Publication Date: Rev.4.00, January 29, 2004
Published by:
Sales Strategic Planning Div.
Renesas Technology Corp.
Edited by:
Technical Documentation & Information Department
Renesas Kodaira Semiconductor Co., Ltd.
2004 Renesas Technology Corp. All rights reserved. Printed in Japan.
SH7144 Group FP-112B
User System Interface Board
HS7144ECH61H User’s Manual
REJ10B0038-0400H
|