Use & Care Manual
Single-Door
Freezer
Welcome & Congratulations
2
Safety Instructions
Installation
2-3
3-4
4
Temperature Controls
Looking Inside
5
Food Storage
& Energy Saving Tips
5-6
6
Ice Service
Care & Cleaning
Warranty
7
8
BeforeYou Call
9-10
P/N 297081400 (Jan 2006)
READ AND SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
INSTALLATION
This Owner’s Guide provides specific operating instructions for
your model. WUseAtRheRfrAeeNzeTrYonlIyNaFsOinsRtrMucAteTd IinOtNhis Owner’s
WARNING
ELECTRICAL INFORMATION
Guide. Before starting the freezer, follow these important first
steps.
These guidelines must be followed to ensure that safety
mechanisms in the design of this freezer will operate properly.
INSTALLATION
•
Choose a place that is near a grounded electrical outlet. Do
•
Refer to the serial plate for correct electrical rating.
The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
shock hazards. It must be plugged directly into a
properly grounded three-prong receptacle. The power
supply circuit must be installed in accordance with
current edition of the National Electrical Code (NFPA
70) and local codes and ordinances. Consult a qualified
electrician. Receptacles protected by Ground Fault
Circuit Interrupters (GFIC) are NOT RECOMMENDED.
Do not use an extension cord or adapter plug.
If voltage varies by 10% or more, freezer performance
may be affected. Operating freezer with insufficient
power can damage the motor. Such damage is not
covered under the warranty. If you suspect your house
hold voltage is high or low, consult your power company
for testing.
Not use an extension cord or an adapter plug.
•
For the most efficient operation, the freezer should be
located where surrounding temperatures will not drop
below 40° F (5° C) or exceed 110° F (43° C).
•
•
Allow the following clearances for ease of installation,
proper air circulation, and electrical connections:
Sides
Back & Top
3/8”
1”
Do Not block the toe grille on the lower front of your
freezer. Sufficient air circulation is essential for the proper
operation of your freezer.
•
Refrigerator
•
•
To prevent the freezer from being turned off
accidentically, do not plug unit into an outlet controlled
by a wall switch or pull cord.
Do not pinch, knot, or bend the cord in any manner.
OTHER PRECAUTIONS
•
•
To defrost freezer, always unplug unit first.
Never unplug the freezer by pulling on the cord. Always grip
the plug firmly, and pull straight out from the receptacle.
NOTE
Freezer
Turning the temperature control to OFF turns off the
compressor, but does not disconnect the power to the light
bulb or other electrical components.
Installation
NOTE
The exterior walls of the freezer may become quite warm as
the compressor works to transfer heat from the inside.
Temperatures as much as 30° F warmer than room
temperature can be expected.
WARNING
Avoid fire hazard or
electric shock. Do not
use an extension cord
or an adapter plug. Do
not remove any prong
from the power cord.
DOOR OPENING
NOTE
If your freezer is placed with the door hinge side against a
wall, you may have to allow additional space so the door can
be opened wider.
FI3RST
LEVELING
DOOR REMOVAL
If door must be removed:
The freezer must have all bottom corners resting firmly on a
solid floor. The floor must be strong enough to support a fully
loaded freezer. NOTE: It is Very Important for your freezer to be
level in order to function properly. If the freezer is not leveled
during installation, the
1. Gently lay freezer on its back, on a rug or blanket.
2. Remove two base screws and base panel.
3. Remove bottom hinge screws.
4. Remove plastic top hinge cover.
5. Remove screws from top hinge.
6. Remove top hinge from cabinet.
7. Remove door and bottom hinge from cabinet.
8. To replace door, reverse the above order and manner of
removal. Securely tighten all screws to prevent hinge
slippage.
door may be misaligned
and not close or seal
properly, causing
Turn
Left To
Raise
cooling, frost, or moisture
problems.
Turn
Right To
Lower
Plastic
Leveling Feet
To Level Freezer:
After discarding crating
screws and wood base,
Crating
Screw
ICE MAKER INSTALLATION
use a carpenter’s level to
level the freezer from
front-to-back. Adjust the
plastic leveling feet in
front, ½ bubble higher, so
that the door closes
If your Freezer has an automatic ice maker, please refer to the
two inserts in the bond pack that came with your Freezer (1.
Installation Instructions & 2. Installation - Connecting Ice Maker
to Water Supply) to correctly hook-up your ice maker.
Discard The (4) Crating Screws
And (2) Wood Bases
easily when left halfway
TEMPERATURE CONTROLS
open.
Unpacking and Leveling
COOL DOWN PERIOD
•
For safe food storage, allow 4 hours for the freezer to
cool down completely. The freezer will run continuously
for the first several hours. Foods that are already frozen
may be placed in the freezer after the first few hours of
operation. Unfrozen foods should NOT be loaded into
the freezer until the freezer has operated for 4 hours.
When loading the freezer, freeze only 3 pounds of
fresh food per cubic foot of freezer space at one time.
Distribute packages to be frozen evenly throughout the
freezer. It is not necessary to turn the control knob to a
colder setting while freezing food.
Leveling Instructions for all Refrigerator/Freezer Pair:
•
Remove two leg levelers provided in literature bag. While
unit is lying on its back for wood skid removal, install both
leg levelers in rear of unit.
•
•
•
Level door of first unit using all four levelers and slide unit
into place. Recheck for levelness and adjust if necessary.
Measure distance from floor to bottom of door on first unit.
Adjust and level second unit so door height matches.
•
Leg Level Adjustments
•
•
One full turn of all four leg levelers will raise door 5/32”.
One full turn of both front leg levelers will raise door
3/16” and tilt top of door back 7/16”.
TEMPERATURE CONTROL
•
•
One full turn of both rear leg levelers will lower door
1/32” and tilt top of door forward 7/16”.
One full turn of both side leg levelers will raise door
3/16” and tilt top of door 3/8”.
The temperature control is located
inside the freezer on upright models.
The temperature is factory preset to
provide satisfactory food storage
temperatures. However, the
temperature control is adjustable to
provide a range of temperatures for
your personal satisfaction. If a colder
•
•
Slide second unit into place leaving a minimum gap of 3/16”
between units for door swing clearance.
This last step may require at least one extraction of the
second unit to properly align units in a “built-in” application.
Cold Control
temperature is desired, turn the temperature control knob
toward COLDEST and allow several hours for temperatures to
stabilize between adjustments.
CAUTION
To allow door to close and
seal properly, do not let
food packages extend past
the front of the shelves.
Shelf Front
FI4RST
MID LEVEL LIGHTING
LOOKING INSIDE
The lights comes on automatically when the door is opened. To
replace the light bulb, turn the temperature control to OFF and
unplugtheelectricalcord.Removethelensfromthelamphousing
by unsnapping it from the lamp housing using your fingers or a
screwdriver. Be careful not to break the locking tabs on the lamp
housing. Replace the old bulb with a bulb of the same type and
wattage. To replace the lens, snap one side of the lens opening to
the tab on the lamp housing. Then carefully attach the other side.
INTERIOR LIGHTING
The lights comes on automatically when the door is opened. To
replace the light bulb, turn the temperature control to OFF and
unplug the electrical cord. Replace the old bulb with a bulb of
the same wattage.
SLIDE-OUT BASKET
A Slide-Out Basket located at
the bottom of the freezer,
provides separate storage
space for items that are difficult
to store on freezer shelves. To
remove the basket, pull out and
lift up.
TILT-OUT SHELF
This shelf is located
inside on the freezer
door and provides
additional storage
space. To access an
item, tilt top of “basket”
shelf down.
FOOD STORAGE AND
ENERGY SAVING TIPS
ADJUSTABLE INTERIOR
SHELVES
•
•
The freezer should be located in the coolest
area of the room, away from heat producing
appliances or heating ducts, and out of
direct sunlight.
Let hot foods cool to room temperature
before placing in the freezer. Overloading
Multi-position adjustable interior
shelves can be moved to any
position for larger or smaller
packages. The shipping spacers
that stabilize the shelves for
shipping may be removed and
discarded.
the freezer forces the compressor to run longer. Foods that
freeze too slowly may spoil or lose quality.
Be sure to wrap foods properly, and wipe containers dry
before placing them in the freezer. This cuts down on
frost build-up inside the freezer.
Freezer shelves should not be lined with aluminum foil,
wax paper, or paper toweling. Liners interfere with cold
air circulation, making the freezer less efficient.
Organize and label food to reduce door openings and
extended searches. Remove as many items as needed
at one time, and close the door as soon as possible.
•
•
•
TO ADJUST CANTILEVER
SHELVES
NOTE
Cantilever shelves are supported at the back of the freezer.
VACATION AND MOVINGTIPS
ShortVacations:
1
2
Lift front edge up.
Pull shelf out.
Leave the freezer operating during vacations of less
than three weeks.
Replace the shelf by
inserting the hooks at rear of
the shelf into the wall
bracket. Lower the shelf into
the desired slots and lock
into position.
Long Vacations:
If the freezer will not be used for several months:
•
•
•
Remove all food and unplug the power cord.
Clean and dry the interior thoroughly.
Leave the freezer door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
FI5RST
Moving: When moving the freezer, follow these
TURNINGYOUR ICE MAKER OFF
guidelines to prevent damage:
To stop the ice maker, lift the wire signal arm until it clicks and
locks in the “up” or OFF position. The ice maker also turns off
automatically when the ice container is full. If your model has an
adjustable freezer shelf, place the shelf in the lower position, so
that the wire signal arm will hit the ice when the container is full.
•
•
•
Disconnect the power cord plug from the wall outlet.
Remove foods, then defrost, and clean the freezer.
Secure all loose items such as base panel, baskets, and
shelves by taping them securely in place to prevent
damage.
IMPORTANT
•
In the moving vehicle, secure freezer in an upright
position to prevent movement. Also protect outside of
freezer with a blanket, or similar item.
Check the leveling bracket on the ice maker to ensure the ice
maker is level. If the gap between the freezer wall and the ice
maker is the same at top and bottom, then the ice maker is
level.
POWER FAILURE / FREEZER FAILURE
NOTE
Your ice maker is shipped with the wire signal arm in the ON
position. To ensure proper function of your ice maker, hook up
water supply immediately or turn ice maker OFF by lifting the
wire signal arm until it clicks and locks in the UP position.
Do not open freezer door unnecessarily if freezer is off for
several hours.
If a power failure occurs, frozen foods will stay frozen for at
least 24 hours if the freezer is kept closed. If the power failure
continues, pack seven or eight pounds of dry ice into the freezer
every 24 hours. Look in the Yellow Pages under Dry Ice, Dairies,
or Ice Cream Manufacturers for local dry ice suppliers. Always
wear gloves and use caution when handling dry ice.
Leveling Bracket
Ice
Container
If the freezer has stopped operating, see Freezer Does Not
Run in the Troubleshooting Guide. If you cannot solve the
problem, call Sears Service immediately.
If the freezer remains off for several hours, follow the directions
above for the use of dry ice during a power failure. If necessary,
take the food to a local locker plant until the freezer is ready to
operate. Look in the Yellow Pages under Frozen Food Locker
Plants.
1” or less
ICE MAKERTIPS
ICE SERVICE
•
Ice cubes stored too long may develop an odd flavor.
Empty the ice container and ensure that the wire signal
arm is in its “down” or ON position. The ice maker will
then produce more ice.
If your freezer has an automatic ice maker, it will provide a
sufficient supply of ice for normal use. During the initial startup
of your freezer, however, no ice will be produced during the first
24 hours of operation. Automatic ice makers are also optional
accessories that may be installed in some models at any time.
Call your local dealer for information.
•
•
Occasionally shake the ice container to keep ice
separated.
Keep the wire signal arm in its “up” or OFF position until
the freezer is connected to the water supply or whenever
the water supply is turned off.
TURNINGYOUR ICE
MAKER ON
•
The following sounds are normal when the ice maker is
operating:
After the plumbing
•
•
•
•
•
Motor running
connections have been
completed, the water
supply valve must be
opened. Place the ice
container under the ice
maker, pushing it as far
back as possible. Lower
the wire signal arm to its
“down” or ON position.
Ice loosening from tray
Ice dropping into ice container
Running water
Water valve opening or closing
•
Wash the ice container in warm water with mild detergent.
Rinse well and dry.
CAUTION
Ice Maker
New plumbing
connections may cause
Do Not place the ice container in your dishwasher.
the first production of ice cubes to be discolored or have an odd
flavor. These first cubes should be discarded until the cubes
produced are free of discoloration and taste.
•
•
Stop the ice maker when cleaning the freezer and during
vacations.
If the ice maker will be turned off for a long period of time,
turn the water supply valve to the closed position.
FI6RST
CARE AND CLEANING
Keep your freezer clean to prevent odor build-up. Wipe up any
NOTE
spills immediately and clean at least twice a year. Never use
metallic scouring pads, brushes, abrasive cleaners or strong
alkaline solutions on any surface. Do not wash any removable
parts in a dishwasher. Always unplug the electrical power cord
from the wall outlet before cleaning.
•
Turning the freezer temperature control to “OFF” turns off
the compressor, but does not disconnect electrical
power to the light bulb or other electrical components. To
turn off power to your freezer, you must unplug the
power cord from the wall outlet.
•
Do not use razor blades or other sharp instruments which
can scratch the appliance surface when removing
adhesive labels. Any glue left from tape or labels can be
removed with a mixture of warm water and mild
detergent, or, touch the glue residue with the sticky side of
tape you have already removed. Do not remove the
serial plate.
CAUTION
•
•
When moving the freezer, pull straight out. Do not shift
the freezer from side to side as this may tear or gouge
the floor covering.
Damp objects stick to cold metal surfaces. Do not
touch interior metal surfaces with wet or damp hands.
Care & Cleaning Chart
Part
What To Use
Tips and Precautions
Interior/Door
Liner
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to
wring excess water out of sponge or cloth before cleaning around
controls, light bulb or any electrical part.
•
•
Soap and water
Baking soda and water
Wipe gaskets with a clean soft cloth.
Door Gaskets
Drawers/Bins
Glass Shelves
•
•
Soap and water
Soap and water
Do not wash any removable items (bins, drawers, etc.) in dishwasher.
Allow glass to warm to room temperature before immersing in warm
water.
•
•
•
•
•
Soap and water
Glass cleaner
Mild liquid sprays
Soap and water
Non Abrasive Glass
Cleaner
Do not use commercial household cleaners, ammonia, or alcohol to clean
handles. Use a soft cloth to clean smooth handles. Do Not use a dry
cloth to clean smooth doors.
Exterior and
Handles
Clean stainless steel front and handles with soapy water and a dishcloth.
Rinse with clean water and a soft cloth. Wipe stubborn spots with an
ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless
steel cleaner. These cleaners can be purchased at most home
improvement or major department stores. Always follow manufacturer's
instructions.
•
•
•
Soap and water
Ammonia
Stainless Steel
Cleaners
Exterior and
Handles
(Stainless
Steel Models
Only)
NOTE: Always clean, wipe and dry with the grain to prevent cross-
grain scratching. Wash the rest of the cabinet with warm water and mild
liquid detergent. Rinse well, and wipe dry with a clean soft cloth.
FI7RST
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
Canada
1.800.944.9044
Electrolux Major Appliances
North America
1.800.668.4606
Electrolux Canada Corp.
5855 Terry Fox Way
P.O. Box 212378
Augusta, GA 30907
Mississauga, Ontario, Canada
L5V 3E4
FI8RST
BEFORE YOU CALL
Before calling for service, review this list. It may save you time and expense. This list
includes common occurences that are not the result of defective workmanship or
materials in this appliance.
TROUBLESHOOTING
GUIDE
PROBLEM
FREEZER DOES NOT RUN
Freezer does not run.
CAUSE
CORRECTION
• Freezer is plugged into a circuit
that has a ground fault interrupt.
• Temperature control is in the
OFF position.
• Use another circuit. If you are unsure about the outlet,
have it checked by a certified technician.
• See Setting the Temperature Control Section.
• Freezer may not be plugged in,
or plug may be loose.
•
Ensure plug is tightly pushed into outlet.
• House fuse blown or tripped
circuit breaker.
• Check/replace fuse with a 15 amp time-delay fuse. Reset
circuit breaker.
• Power outage.
• Check house lights. Call local Electric Company.
• Room or outside weather is hot.
• It's normal for the freezer to work harder under these
conditions.
Freezer runs too much or too
long.
• Freezer has recently been
disconnected for a period of
time.
• It takes 4 hours for the freezer to cool down completely.
• Large amounts of warm or hot
food have been stored recently.
• Warm food will cause freezer to run more until the
desired temperature is reached.
• Doors are opened too frequently • Warm air entering the freezer causes it to run more.
or too long.
Open doors less often.
• Freezer door may be slightly
open.
• See "DOOR PROBLEMS" Section.
• Temperature Control is set too
low.
• Turn control knob to a warmer setting. Allow several hours
for the temperature to stabilize.
• Freezer gasket is dirty, worn,
cracked, or poorly fitted.
• Clean or change gasket. Leaks in the door seal will cause
freezer to run longer in order to maintain desired
temperature.
• Temperature Control is set too
low.
• Turn the control to a warmer setting. Allow several hours
for the temperature to stabilize.
Interior Freezer temperature is
too cold.
• Temperature Control is set too
warm.
• Turn control to a colder setting. Allow several hours for the
temperature to stabilize.
Interior Freezer temperature is
too warm.
• Door is kept open too long or is
opened too frequently.
• Door may not be seating
properly.
• Warm air enters the freezer every time the door is
opened. Open the door less often.
• See "DOOR PROBLEMS" Section.
• Large amounts of warm or hot
food may have been stored
recently.
• Wait until the freezer has had a chance to reach its
selected temperature.
• Freezer has recently been
disconnected for a period of
time.
• Freezer requires 4 hours to cool down completely.
• The external freezer walls can
be as much as 30°F warmer
than room temperature.
• This is normal while the compressor works to transfer
heat from inside the freezer cabinet.
Freezer external surface
temperature is warm.
SOUND AND NOISE
• Modern freezers have increased • This is normal. When the surrounding noise level is low,
Louder sound levels whenever
freezer is on.
storage capacity and more
stable temperatures. They
require a high efficiency
compressor.
you might hear the compressor running while it cools the
interior.
• Freezer operates at higher
pressures during the start of the
ON cycle.
• This is normal. Sound will level off or disappear as freezer
continues to run.
Longer sound levels when
compressor comes on.
FI9RST
BEFORE YOU CALL
CAUSE
PROBLEM
CORRECTION
SOUND AND NOISE (Cont.)
• Metal parts undergo expansion • This is normal. Sound will level off or disappear as
Popping or cracking sound
when compressor comes on.
and contraction, as in hot water
pipes.
freezer continues to run.
• Refrigerant (used to cool
freezer) is circulating
• This is normal.
Bubbling or gurgling sound,
like water boiling.
throughout the system.
• Freezer is not level. It rocks on
the floor when it is moved
slightly.
• Level the unit. Refer to "Leveling" in the First Steps
Section.
Vibrating or rattling noise.
• Floor is uneven or weak.
Freezer rocks on floor when it
is moved slightly.
• Ensure floor can adequately support freezer. Level the
freezer by putting wood or metal shims under part of the
freezer.
• Freezer is touching the wall.
• Relevel the freezer or move freezer slightly. Refer to
"Leveling" in the First Steps Section.
WATER/MOISTURE/FROST INSIDE FREEZER
• Weather is hot and humid,
which increases internal rate of
frost build-up.
• This is normal.
Moisture forms on inside
freezer walls.
• Door may not be seating
properly.
• See "DOOR PROBLEMS" Section.
• Door is kept open too long, or
is opened too frequently.
• Open the door less often.
WATER/MOISTURE/FROST OUTSIDE FREEZER
• Door may not be seating
• See "DOOR PROBLEMS" Section.
Moisture forms on ouside of
freezer.
properly, causing the cold air
from inside the freezer to meet
warm moist air from outside.
ODOR IN FREEZER
Odors in freezer
• Interior needs to be cleaned.
• Foods with strong odors are in
the freezer.
• Clean interior with sponge, warm water, and baking
soda.
• Cover the food tightly.
DOOR PROBLEMS
Door will not close.
• Freezer is not level. It rocks on
the floor when it is moved
slightly.
• This condition can force the cabinet out of square and
misalign the door. Refer to "Leveling" in the First Steps
Section.
• Floor is uneven or weak.
Freezer rocks on floor when it
is moved slightly.
• Level the floor by using wood or metal shims under the
freezer or brace floor supporting the freezer.
LIGHT BULB IS NOT ON
Light bulb is not on.
• Light bulb is burned out.
• Follow directions under "Interior Light" or "Mid Level
Light" in the Freezer Features Section.
• No electric current is reaching
the freezer.
• See "FREEZER DOES NOT RUN" Section.
AUTOMATIC ICE MAKER
• Ice maker is not working
Automatic ice maker not
working. (some models)
• Ensure the wire signal arm is not in the UP position.
• Water supply is turned off.
• Water pressure is too low.
• The freezer is not cold enough.
FI10RST
|