Sanyo Security Camera VCC ZM400 User Guide

INSTRUCTION MANUAL

MANUEL D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

VCC-ZM400

COLOR CCD ZOOM camera

Caméra CCD COULEURS avec ZOOM

Cámara CCD ZOOM A COLOR

About this manual

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

Acerca de este manual

Lea cuidadosamente este manual antes de instalar y usar

la cámara. Asegúrese de guardarlo a su alcance para

futuras consultas.

À propos de ce manuel

Avant d’installer et d’utiliser la caméra, veuillez lire ce manuel

attentivement. Gardez-le à portée de main pour toute référence

ultérieure.

INFORMATION TO USER

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

Safety Guard

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications.

THIS SYMBOL INDICATES THAT THERE ARE

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE LITERATURE

ACCOMPANYING THIS UNIT.

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or

more of the following measures:

NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and

receiver.

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme à la

norme NMB-003 du Canada.

– Consult the dealer or an experienced radio/TV technician for

help.

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must

accept any interference received, including interference that

may cause undesired operation.

This installation should be made by a qualified service person and

should conform to all local codes.

Changes or modifications not expressly approved by Sanyo

may void the user’s authority to operate this camera.

PRECAUTIONS

In case of problem

Protect from high temperatures

Do not use the camera if smoke or a strange odour comes from

the unit, or if it seems not to function correctly. Disconnect the

power cord immediately, and consult your dealer (or a Sanyo

Authorized Service Centre).

Do not install close to stoves, or other heat generating devices,

such as spotlights, etc., or where it could be subject to direct

sunlight, as that could cause deformation, discoloration or other

damages.

Be careful when installing close to the ceiling, in a kitchen or

boiler room, as the temperature may raise to high levels.

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause

damage to the unit. For internal settings and repairs, consult your

dealer (or a Sanyo Authorized Service Centre).

Install where the temperature range will stay between –10°C and

50°C. (no condensation)

Cleaning

Do not put objects inside the unit

• Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with

a soft detergent solution and wrung dry, then wipe dry with a

dry soft cloth.

Make sure that no metal objects or flammable substance get

inside the camera. If used with a foreign object inside, it could

cause a fire, short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power

cord immediately, and consult your dealer (or a Sanyo Authorized

Service Centre). Be careful to protect the camera from rain, sea

water, etc.

• Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling.

Before using a chemical cloth, make sure to read all

accompanying instructions. Make sure that no plastic or

rubber material comes in contact with the cabinet for a long

period of time, as that may cause damage or paint peeling.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to

strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high,

or where there is a lot of dust.

PARTS NAMES AND FUNCTIONS

4 SET button (SET) (See p8)

Control

Connect the camera to the monitor, then press the SET

button for about 3 seconds to display the on-screen menu.

5 RS-485 control push-lock terminals (RS485, A, B, G)

terminals

SET

Use a cable thicker than AWG22.

ZOOM

COM

OUT

FOCUS

ALARM

RS485

A: Twisted-pair cable terminal

G: Ground terminal

VIDEO OUT

POWER

AC24V

B: Twisted-pair cable terminal

GND

6 24 V AC or 12 V DC input terminals (AC 24 V, DC 12 V,

GND)

DC12V

CLASS 2 WIRING

Lens cap

1 Video output connector (VIDEO OUT: BNC type)

The cap is installed to protect the lens section. Remove the cap

when using the camera.

Connect this connector to a device such as a time lapse VCR or

monitor with a VIDEO IN connector.

2 Power indicator (POWER)

Comes on when the power to the camera is on.

Note: After connecting the power supply the POWER indicator

will blink for 5 seconds. During this time no adjustments

using the menus or any other operation are possible.

3 Cursor button (See p8)

j: Press this button to move the cursor up.

c: Press this button to move the cursor to the right, or to

turn the settings ON/OFF etc.

d: Press this button to move the cursor to the left, or to turn

the settings ON/OFF etc.

l: Press this button to move the cursor down.

PARTS NAMES AND FUNCTIONS

Camera installation bracket

Control terminals

The bracket can be fixed at the top or bottom of the camera.

1 Zoom terminal (ZOOM)

Sets the zoom to wide angle or telescoping.

2 Focus terminal (FOCUS)

CAUTION: When installing the camera bracket, select a location

that can support the total weight of the camera and

accessories.

Sets the focus to infinite or close range.

3 Grounding terminal (COM)

4 Alarm output terminal (ALARM OUT)

A detection alarm based on the motion sensor is sent to

connected equipment such as a buzzer or lamp or a time

lapse VCR device.

5 Alarm input and color/black & white selection

terminal (ALARM IN)

• When using this terminal for alarm input, connect an

external alarm switch for detecting intruders.

• This terminal can also be used for selecting color or black &

white input. It can be used to force selection of color or

black & white mode by external operation.

Note: The ALARM IN terminal can only receive one type of

input at a time. When using this terminal, use the

ALARM settings to set the type of input. (See p57)

12345

ZOOM

COM IN

FOCUS

ALARM OUT

CONNECTIONS

Basic connection for monitoring or recording

TV monitor

(sold separately)

AC 24 V connection

DC 12 V connection

(A)

AC24V

GND

DC12V

CLASS

WIR

DC12V

CLASS

WIR

Fig. 1

Fig. 2

(Video signal connections)

Time lapse VCR or

: VIDEO IN

Digital video recorder

: VIDEO OUT

(sold separately)

The peripheral devices (VCR, monitor, lens, etc.) and cables

are sold separately.

CAUTION:

To prevent camera and/or power supply failure, pay close

attention to polarity when making the connections.

1 ^{Make the video signal connection between the camera}

and the monitor or time lapse VCR.

2 ^{Power supply choices}

3 ^{Insert the plug of this power supply into a wall outlet.}

• When using a commercially available 24 V AC adaptor,

make sure to use a cable with an earth line (22AWG or

more) to connect to the grounding terminal. (Fig.1.)

The POWER indicator (A) will light. Adjust the picture on the

monitor using the Brightness and Contrast controls.

• When using a DC 12 V power supply, make the

connections as indicated in Fig. 2.

CONNECTIONS

Coaxial cable type and maximum length

• Cable type RG-59U (3C-2V), 250 m maximum.

• Cable type RG-6U (5C-2V), 500 m maximum.

• Cable type RG-11U (7C-2V), 600 m maximum.

Connection of peripheral equipment and

controller terminal

External alarm

switch or color/

black & white select

switch

CAUTION:

Buzzer or lamp

• The RG-59U type cable should not be run through electrical

conduits or through the air.

• Focus adjustment

DC+6V/12V: Infinite

DC–6V/12V: Close range

• Using CCTV/Video-grade coaxial cable.

• Zoom adjustment

DC+6V/12V: Wide angle

DC–6V/12V: Telescoping

A B

CAMERA IN

terminal

Multiplexer

(sold separately)

GAB

RS-485 connector

System controller (sold separately)

DISPLAYING/CLOSING THE MENU SCREEN

MAIN MENU screen

Sub-menu screen

MAIN MENU

LANGUAGE

CAMERA ID

SYNC

SET ‚

OFF

LANGUAGE

ENGLISH

FRENCH

SET

LANGUE

IDIOMA

INT

SPANISH

PRIVACY MASK

LENS

SET ‚

OFF

MIRROR

VIEW SETTING

OPTION

‚

SET ‚

OFF

PRESET

END

BACK

Cursor button SET button

1 ^{Press the SET button for about 3 seconds.}

3 ^{Switching to sub-menu screens}

The MAIN MENU screen will appear.

Use the cursor button (j l d c) until an item with a “y”

next to it is flashing, then press the SET button.

2 ^{Using the cursor button}

4 ^{Closing a settings screen}

1 Use the cursor button (l) to move the cursor down.

When the cursor reaches the bottom of the screen, it goes

back up to the top of the screen.

• To return to the previous screen, use the cursor button (l)

to select BACK for MENU, then press the SET button.

2 Use the cursor button (j) to move the cursor up. When

the cursor reaches the top of the screen, it goes back

down to the bottom of the screen.

• To return to the normal screen, use the cursor button (d or

c) to select END for MENU, then press the SET button.

ꢀ Returning to the default setting

Use cursor button (l, then d or c) to change the PRESET

setting to ON, then press the SET button.

3 Use the cursor button (c) to move the cursor to the right.

This button is also used to change ON/OFF settings etc.

4 Use the cursor button (d) to move the cursor to the left.

This button is also used to change ON/OFF settings etc.

MENU ITEM FLOW AND MENU OPERATION

MAIN MENU

1 2 3 4 5 6 7 8

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

LANGUAGE setting (See p10)

MIRROR setting (See p32)

Choose from among English, French and Spanish.

The image can be rotated horizontally then vertically or vertically

then horizontally.

CAMERA ID setting (See p11)

SYNC setting (See p12)

VIEW SETTING (See p33)

Different detailed settings can be made for each camera (9

screens). After they are set, these are linked to “VIEW SETTING

(0 – 8)” settings for preset positions.

Sets camera to internal synchronization (INT) or power source

synchronization (L-L).

Power source synchronization, the vertical synchronization phase

as adjusted on a sub-menu screen.

OPTION setting (See p56)

For setting communications conditions and alarms.

PRIVACY MASK setting (See p13)

This covers an area of the screen with a gray pattern for areas

that may infringe on privacy.

Gray patterns can be placed on up to 4 areas.

LENS setting (See p17)

This lets you make settings such as automatic and manual focus

settings, zoom speed and zoom ratio. In addition, it can also be

used for automatic switching to color images during daytime, or

to black and white images at times of low luminance such as

nighttime.

LANGUAGE SETTING

Select one of the languages shown on the menu screen (English, French, Spanish).

MAIN MENU

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

LANGUAGE

ENGLISH

FRENCH

SPANISH

LANGUE

IDIOMA

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

LANGUE

PRESET

LANGUAGE

LANGUE

ANGLAIS

FRANCAIS

ESPAGNOL

IDIOMA

RETOUR

1 ^{In the MAIN MENU, use the cursor button (}^j^or^l^{) to}

select SET for LANGUAGE, then press the SET button.

The LANGUAGE screen will appear.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

language (e.g. FRENCH) then press the SET button.

The interface language becomes French.

3 ^{Use the cursor button (}^j^or^l^{) to select RETOUR for}

MENU, then press the SET button.

The MENU PRINCIPAL screen will reappear.

Information in the MAIN MENU screen will appear in the

selected language.

ꢀ Use the cursor button (l) to select FIN, then press the

SET button. The display will return to the normal

monitor screen.

CAMERA ID SETTING

Camera ID setting

Camera ID screen

Example: Setting the Camera ID to “CAM 1”

CAMERA ID SETTING

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

MAIN MENU

CAMERA ID SETTING

LANGUAGE

CAMERA ID

SYNC

SET

INT

SET

OFF

SET

OFF

END

‚

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

ID ????????????????

PRIVACY MASK

LENS

‚

POSITION

SET

‚

ID ????????????????

MIRROR

PRESET

OFF

BACK

VIEW SETTING

OPTION

‚

POSITION

SET

‚

PRESET

OFF

BACK

1 Character selection palette:

By moving the cursor to letters or numbers in this palette,

you can select characters.

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

CAMERA ID, and then use the cursor button (d or c) to

change the setting to ON. Then press the SET button.

Selected characters will appear in the corresponding field

under ID.

The CAMERA ID SETTING screen will appear.

2 ID:

2 ^{Use the cursor button (}^{j l d c}^{) to move the cursor to}

the letter “C” in the character selection palette, then

press the SET button.

When CAMERA ID is set to “OFF”, the 16 characters in the

ID field will all change to “?” but will not be displayed on

the screen. In addition, when the setting is “ON”, “?”

characters will appear on the screen when no ID has been

entered.

ꢀ After at least one character is displayed in the ID field,

the carriage return mark (y) will appear at the lower

right corner of the character selection palette. Selecting

this mark between the characters of the field will create

a new line at that place.

3 POSITION:

After characters are displayed in the ID field, moving the

cursor to the POSITION field with the cursor button and

pressing the SET button will display the camera ID on the

normal screen.

3 ^{Use the same steps to select “A”, “M” and “1” from the}

palette, then press the SET button.

4 PRESET:

The characters “CAM1” appear in the ID field.

When this item is turned to ON, the ID fields are cleared

(question marks appear). Use this function when you want

to change the ID.

ID CAM1????????????

CAMERA ID SETTING

SYNC SETTING (SYNC)

Default setting is internal synchronization (INT), so it does not

need to be set again. Follow the steps below to change the

setting to power source synchronization (L-L).

4 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

POSITION, and then press the SET button.

The camera ID will be displayed on one line.

Power source synchronization (L-L) setting

CAMERA ID SETTING

CAM1

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

MAIN MENU

L-L SETTING

(V SYNC PHASE)

ú------+------ü

Camera ID

ID CAM1????????????

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

POSITION

SET

‚

PRESET

OFF

BACK

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

(Displaying the ID on 2 lines.)

PRESET

OFF

BACK

1 Use the cursor button (d or c) to move the cursor to the

location in the ID field where the carriage return is wanted.

Use the cursor button (j l d c) to select L-L for

SYNC, then press the SET button.

The L-L SETTING screen will appear.

2 Use the cursor button (j l d c) to move the cursor to

the carriage return mark (y) at the lower right corner of

the character selection palette, and then press the SET

button.

Use the cursor button (d or c) to adjust the position

of the vertical synchronization indicator shown on the

screen.

The numerical value will change, allowing adjustment of

vertical synchronization.

5 ^{Moving the on-screen title display position}

Use the cursor button (j l d c) to move the title

display to the preferred position on the screen, then

press the SET button.

The CAMERA ID SETTING screen will reappear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

PRIVACY MASK SETTING (PRIVACY MASK)

Mask setting

MAIN MENU

PRIVACY MASK SETTING

PASSWORD LOCK ON ‚

MASK NO.SELECT

MASK 3 SET

(POSITION)

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

MASK

OFF

SET

OFF

‚

MIRROR

VIEW SETTING

OPTION

‚

MASK NO.SELECT

OFF

PRESET

OFF

BACK

SET

‚

MASK

OFF

1 ^{Use the cursor button (}^j^or^l^{) to select SET for}

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to a}

mask number (e.g. MASK 3), and then use the cursor

button (c) to change the setting to SET. Then press the

SET button.

PRIVACY MASK, then press the SET button.

The PRIVACY MASK SETTING screen will appear.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

The MASK 3 SET (POSITION) screen will appear, and SETy

will be blinking. The gray mask will appear in the center of the

screen.

SET for MASK SET and press the SET button.

The MASK NO. SELECT screen will appear.

Cursor button operation

Note: When PASSWORD LOCK is ON, moving the cursor to

MASK SET and press the SET button to bring up a

password access screen. The password must be entered in

this screen.

OFF: to c side (ON appears), to c side again (SET appears)

• SET: Mask POSITION and SIZE can be set

• ON: Masks can be displayed

• OFF: Masks can be deleted

PRIVACY MASK SETTING (PRIVACY MASK)

(About the POSITION screen)

MASK 3 SET

(SIZE)

MASK 3 SET

It is possible to set as many as 4 masks on the same POSITION

screen.

MASK 1

SET

‚

PRESET

OFF

BACK

4 ^{Use the cursor button (j l d c) to move the gray}

mask, then press the SET button.

The SIZE screen will appear, and the mask that was positioned

in the POSITION screen will be displayed.

5 ^{Use the cursor button (j l d c) to adjust the size of}

the gray mask, then press the SET button.

PRESET and MENU will appear at the bottom of the screen.

Move the cursor to BACK for MENU and press the SET button.

The screen will return to MASK NO. SELECT.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

PRIVACY MASK SETTING (PRIVACY MASK)

PASSWORD setting

You can lock the privacy masks in place as gray patterns after they have been set. The password requirement is initially set to OFF, but to

begin using it, you must enter the factory set password “1234”.

PRIVACY MASK SETTING

PASSWORD LOCK OFF ‚

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK ON

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

¤¤¤¤

SET ‚

1234

SET ‚

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

OFF for PASSWORD LOCK in the PRIVACY MASK

SETTING screen. Then press the SET button.

3 ^{Use the same steps to enter “2”, “3” and “4”, then press}

the SET button.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again. The PRIVACY MASK SETTING screen

will reappear and “ON” will be blinking for PASSWORD LOCK.

The PASSWORD screen will appear.

2 ^{Enter the factory set password “1234”.}

Use the cursor button (j or l) to select “1”, then use

Note: If a different password is required, “NG” will appear.

Please carefully maintain the password so that it will not be

forgotten.

the cursor button (c).

To move the cursor to the next “*” digit.

1¤¤¤

PRIVACY MASK SETTING (PRIVACY MASK)

PASSWORD LOCK cancellation

PASSWORD changes

For use when PASSWORD LOCK is ON

You can change the password with PASSWORD LOCK in either

the ON or OFF setting.

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK ON

PASSWORD

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

(NOW PASSWORD)

¤¤¤¤

SET ‚

BACK

1234

SET ‚

1234

SET ‚

PASSWORD

PRIVACY MASK SETTING

PASSWORD LOCK OFF ‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

(NOW PASSWORD)

**** SET ‚

(NEW PASSWORD)

****

SET ‚

1 ^{Press the SET button.}

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SET for PASSWORD CHANGE and press the SET button.

The PASSWORD screen will appear.

The PASSWORD (NOW PASSWORD) screen will appear.

2 ^{Enter the factory set password “1234”.}

2 ^{Use the cursor button (}^d^or^c^,^j^{) to enter the current}

Use the cursor button (j or l) to select “1”, then use

password (e.g. 1234), then press the SET button.

the cursor button (c).

The PASSWORD (NEW PASSWORD) screen will appear.

To move the cursor to the next “*” digit.

3 ^{Use the cursor button (}^d^or^c^,^j^{) to enter a new}

3 ^{Use the same steps to enter “2”, “3” and “4”, then press}

password (e.g. 4321), then press the SET button.

the SET button.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again.

The PRIVACY MASK SETTING screen will reappear.

“OK” will appear and BACK for MENU will be blinking. Press

the SET button again. The PRIVACY MASK SETTING screen

will reappear and “OFF” will be blinking for PASSWORD LOCK.

LENS SETTING ITEM FLOW

A FOCUS: (See p18)

MAIN MENU

These settings let you select automatic focus (AUTO) or manual focus. Change the focus settings in

accordance with the monitoring conditions.

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PRIVACY MASK

LENS

‚

B ZOOM: (See p21)

MIRROR

VIEW SETTING

OPTION

‚

These settings let you adjust the speed and zoom ratio when using electronic zoom.

PRESET

C DAY/NIGHT: (See p23)

These settings can be used for automatic switching to color images during daytime, or to black and

white images at times of low luminance such as nighttime. Three modes (AUTO, COLOR and B/W) can

be selected. Change the settings in accordance with the monitoring conditions.

LENS

FOCUS

MANU ‚

SET

D VIEW ANGLE: (See p31)

ZOOM

‚

These settings are for setting the image angle.

If “OVER” is set, the image angle is set to approximately 1.05.

DAY/NIGHT

VIEW ANGLE

AUTO ‚

OFF

PRESET

OFF

BACK

LENS SETTING (LENS)

This item allows adjustment of focus (for manual focus or autofocus) and adjustment of zoom when needed.

A FOCUS setting

ꢀ Setting the manual focus (MANU)

Sets a limit for near distance focusing and sets focus speed for manual focus.

FOCUS SETTING

MAIN MENU

FOCUS SETTING

LIMIT NEAR

SPEED

LIMIT NEAR

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

‚

LIMIT NEAR

SPEED

‚

LENS

FOCUS

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

MANU ‚

SET

ZOOM

‚

1 ^{Use the cursor button (}^j^or^l^{) to select SET for LENS,}

4 ^{SPEED of focus setting}

then press the SET button.

Use the cursor button (j or l) to move the cursor to

SPEED, then use the cursor button (d or c) to select the

focus adjustment speed value. (e.g. 3)

The LENS screen will appear.

2 ^{Use the cursor button (}^d^or^c^{) to select MANU, then}

press the SET button.

Available settings: 1, 2, 3, 4 (Quickest speed)

The FOCUS SETTING screen will appear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

3 ^{LIMIT NEAR focus distance setting}

Use the cursor button (j or l) to move the cursor to

LIMIT NEAR, then use the cursor button (d or c) to

change the distance value. (e.g. 3M)

Available settings: 1M (meter), 3M, 10C (centimeters), 30C,

50C

Note: Focusing becomes difficult when near distance limit is set

to less than “1M”.

LENS SETTING (LENS)

ꢀ Setting the autofocus (AUTO)

Sets a limit for near distance focusing and sets focusing sensitivity and focus target area.

Note: As a normal practice, use manual focus when keeping the camera focused on the same target object for a long period of time

(over 24 hours). This can be used with the one-push autofocus function when needed (operated from the system controller). Long

periods of surveillance with the autofocus in operation will shorten the work life of the lens.

MAIN MENU

LENS

FOCUS SETTING

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

LIMIT NEAR

SENSITIVITY

AREA

HIGH

SET

FOCUS

ZOOM

AUTO ‚

LIMIT NEAR

SENSITIVITY

AREA

LOW

SET

‚

SET

‚

MIRROR

FOCUS SETTING

VIEW SETTING

OPTION

‚

LIMIT NEAR

SENSITIVITY

AREA

PRESET

OFF

BACK

PRESET

OFF

BACK

HIGH

SET

‚

1 ^{Use the cursor button (j or l) to select SET for LENS,}

4 ^{Setting focus SENSITIVITY}

then press the SET button.

Use the cursor button (j or l) to move the cursor to

SENSITIVITY, then use the cursor button (d or c) to

change the setting. (e.g. LOW)

The LENS screen will appear.

2 ^{Use the cursor button (d or c) to select AUTO, then}

Available settings:

press the SET button.

• HIGH: High sensitivity focusing

• LOW: Low sensitivity focusing

The FOCUS SETTING screen will appear.

3 ^{LIMIT NEAR focus distance setting}

Note: When focus SENSITIVITY is set to HIGH, it may react to

even slight movements of the target object. In this case,

change the setting to LOW.

Use the cursor button (j or l) to move the cursor to

LIMIT NEAR, then use the cursor button (d or c) to

change the distance value. (e.g. 3M)

Available settings: 1M (meter), 3M, 10C (centimeters), 30C,

50C

Note: Focusing becomes difficult when near distance limit is set

to less than “1M”.

LENS SETTING (LENS)

FOCUS SETTING

AREA SETTING

LIMIT NEAR

LOW

SET

AREA

SENSITIVITY

AREA

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

6 ^{Use the cursor button (}^d^or^c^{) to select the focus target}

SET for AREA, and press the SET button.

area. (e.g. 3)

The AREA SETTING screen for AREA 2 (default setting) will

appear to allow setting of focus target area.

The focus target area will become narrow.

Available settings: 1/full screen, 2/center of screen,

3/smaller center

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

LENS SETTING (LENS)

B ZOOM setting

Sets zooming speed and magnification power of the electronic zoom. This item also has a setting for improvement of vertical resolution

sensitivity of still pictures.

ZOOM SETTING

SPEED 4

MAIN MENU

LENS

SPEED

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

FOCUS

MANU ‚

SET

EL ZOOM

OFF

EL ZOOM

V-RESO.UP

OFF

ZOOM

‚

PRIVACY MASK

LENS

‚

DAY/NIGHT

AUTO ‚

OFF

MIRROR

VIEW ANGLE

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

3 ^{Zoom speed setting}

1 ^{Use the cursor button (j or l) to select SET for LENS,}

then press the SET button.

Use the cursor button (d or c) to select the zooming

speed. (e.g. 4)

The LENS screen will appear.

Available settings: 1, 2, 3, 4 (Quickest speed)

2 ^{Use the cursor button (j or l) to select SET for ZOOM,}

then press the SET button.

4 ^{EL ZOOM (Electronic zoom) magnification setting}

The ZOOM SETTING screen will appear.

Use the cursor button (j or l) to move the cursor to EL

ZOOM, then use the cursor button (d or c) to select the

electronic zoom magnification power. (e.g. x4)

Available settings: OFF, x2, x4, x8, x16 (16 power)

LENS SETTING (LENS)

ZOOM SETTING

SPEED

EL ZOOM

V-RESO.UP

PRESET

OFF

BACK

5 ^{V-RESO.UP (Vertical resolution sensitivity) setting}

Use the cursor button (j or l) to move the cursor to

V-RESO.UP, then use the cursor button (d or c) to

select the vertical resolution sensitivity. (e.g. ON)

Note: When V-RESO.UP is set to “ON”, vertical resolution

sensitivity for still pictures in the electronic zoom field will

be improved but afterimages of moving objects will be

more conspicuous.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Note:

V-RESO. UP will be automatically set to OFF when any of the

following settings is made.

• IRIS SETTING: SENSE UP (x2...)(See p40)

• VIEW SETTING: SHUTTER (LONG)(See p47)

• D/N SETTING: DNR (ON)(See p25)

LENS SETTING (LENS)

C DAY/NIGHT setting

The DAY/NIGHT mode can be set to one of three settings (AUTO, COLOR or B/W) to improve the appearance of images. This lets you set

the filming mode to color mode during times of normal brightness, or to black & white mode to increase sensitivity when there is less light.

When you select a mode, you may then need to make detailed settings for the respective mode used.

LENS

FOCUS

MANU ‚

SET

ZOOM

‚

DAY/NIGHT

VIEW ANGLE

AUTO ‚

OFF

AUTO,

COLOR,

B/W

PRESET

OFF

BACK

(Fig. 1)

• AUTO: Automatic mode; The mode switches automatically

between color mode and black & white mode depending on

the luminance of the objects being monitored. (See p24)

Note:

• A sound may be heard when the colour image or black and

white image is switched. Also, the image will be distorted as

shown in Fig. 1. This is normal and does not indicate a

problem.

• COLOR: Color mode; Images are filmed in color regardless of

the luminance of the objects being monitored. (See p27)

• B/W: Black & white mode; Images are filmed in black & white

regardless of the luminance of the objects being monitored.

(See p28)

• When using infrared lighting, if there is a strong reflection on

the subject, the optical filter may switch from black and white

to colour mode. Use only enough infrared lighting so that the

mode is not switched.

Note: When “COLOR” is selected, the mode is fixed at color and

you can only view images that are in color. The same

applies to B/W mode. However, you can also use the

ALARM IN terminal on the rear panel to force the mode to

change from COLOR to B/W or from B/W to COLOR. Refer

to the “Color/black & white selection setting” for

details on the setting method. (See p59)

LENS SETTING (LENS)

ꢀ AUTO mode setting

Note:

• If the backlight compensation has been set to “MULTI”, the backlight compensation will be canceled when the mode is switched to

B/W.

• If “SENSE UP” has been activated, SENSE UP mode will be activated after the mode switches to B/W mode.

MAIN MENU

D/N SETTING - AUTO

LENS

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

AGC MAX GAIN

DNR

+9·

OFF

FOCUS

MANU ‚

SET

BURST

ZOOM

‚

PRIVACY MASK

LENS

‚

FOCUS

LEVEL

MID

DAY/NIGHT

AUTO ‚

OFF

MIRROR

VIEW SETTING

OPTION

‚

VIEW ANGLE

PRESET

OFF

BACK

PRESET

OFF

BACK

3 Sets burst suppression. If other peripheral devices (such

as a multiplexer) are connected to the system, bursts

(distortion of image color) can occur when switching

between color and black & white. If this happens,

change the BURST setting to “ON”.

1 ^{Use the cursor button (j or l) to select SET for LENS,}

then press the SET button.

The LENS screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

DAY/NIGHT, use the cursor button (d or c) to select

the mode (e.g. AUTO), and then press the SET button.

4 Sets the focus when switching to black & white mode.

5 Sets the switching level for color mode and black & white

mode. The three available settings are LOW, MID or HIGH.

In addition, the switching level can be set manually (ADJ).

The D/N SETTING - AUTO screen will appear, and the “+9dB”

setting for “AGC MAX GAIN” will be blinking.

1 Sets the maximum AGC gain.

2 Sets the digital noise reduction.

LENS SETTING (LENS)

D/N SETTING - AUTO

AGC MAX GAIN

DNR

+9·

OFF

AGC MAX GAIN

DNR

+9·

OFF

AGC MAX GAIN

DNR

+9·

AGC MAX GAIN

DNR

+9·

BURST

FOCUS

LEVEL

FOCUS

LEVEL

FOCUS

MID

LEVEL

MID

LEVEL

MID

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

3 ^{AGC MAX GAIN setting}

5 ^{BURST setting}

Use the cursor button (j or l) to move the cursor to

AGC MAX GAIN, and then use the cursor button (d or

c) to select the gain.

Use the cursor button (j or l) to move the cursor to

BURST, and then use the cursor button (d or c) to

select the burst setting (e.g. ON).

Available settings:

Available settings: Select the maximum AGC gain from

• ON: The color burst signal is turned on.

• OFF: This should normally be set to “OFF”.

+9dB, +12dB or +15dB.

4 ^{DNR setting}

6 ^{FOCUS setting}

Use the cursor button (j or l) to move the cursor to

DNR, and then use the cursor button (d or c) to select

the digital noise reduction setting (e.g. ON).

Use the cursor button (j or l) to move the cursor to

FOCUS, and then use the cursor button (d or c) to

select the focus setting (e.g. 1).

Available settings:

• ON: DNR (digital noise reduction) is applied. This reduces

interference at low luminance levels.

• 1: Near-infrared wavelength correction is set.

(around 900 nm)

• OFF: DNR is not applied.

• 2: Visible light spectrum is set.

Note: Digital noise reduction operates when the gain control

increases. In addition, blurring and ghosting of images

can occur when moving images are being monitored,

and so the resolution is also reduced slightly.

Note: This is set to “1” at the time of shipment from the

factory. If the images are out of focus, change it to “2”.

LENS SETTING (LENS)

D/N SETTING - AUTO

LEVEL SETTING

(COLOR†B/W)

LEVEL SETTING

(COLOR†B/W)

AGC MAX GAIN

DNR

+9·

OFF

BURST

FOCUS

LEVEL

(B/W†COLOR)

ADJ

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

7 ^{LEVEL setting}

8 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

COLOR†B/W, and then use the cursor button (d or c)

to select the value.

Use the cursor button (j or l) to move the cursor to

LEVEL, use the cursor button (d or c) to select the level

setting (e.g. ADJ) and then press the SET button.

Available settings: 1 – 7

The LEVEL SETTING screen will appear.

Available settings:

Note:

• The larger the value, the darker the switching level.

• LOW: The mode switches when the luminance of the

• Changing the setting for one of the switching level settings

(from color mode to black & white mode or from black &

white mode to color mode) causes the other setting to

change also.

objects being monitored is comparatively dark.

• MID: The mode switches when the luminance of the

objects being monitored is between the LOW and

HIGH levels.

• Set the switching level from black & white mode to color

mode in the same way.

• HIGH: The mode switches when the luminance of the

objects being monitored is comparatively bright.

• ADJ: The switching level for color mode to black & white

mode and for black & white mode to color mode

respectively can be set manually.

LENS SETTING (LENS)

ꢀ COLOR mode setting

MAIN MENU

2, 3

D/N SETTING - COLOR

LENS

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

AGC MAX GAIN

DNR

0·

OFF

FOCUS

MANU ‚

SET

ZOOM

‚

PRIVACY MASK

LENS

‚

DAY/NIGHT

COLOR‚

OFF

MIRROR

VIEW SETTING

OPTION

‚

VIEW ANGLE

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to select SET for LENS,}

3 ^{AGC MAX GAIN setting}

then press the SET button.

Use the cursor button (j or l) to move the cursor to

AGC MAX GAIN, and then use the cursor button (d or

c) to select the gain.

The LENS screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

DAY/NIGHT, use the cursor button (d or c) to select

the level setting (e.g. COLOR) and then press the SET

button.

Available settings: Select the maximum AGC gain from OFF,

–6dB, 0dB, +6dB or +9dB.

Setting fixed gain manually

The D/N SETTING - COLOR screen will appear, and the “ 0dB”

setting for “AGC MAX GAIN” will be blinking.

1 Sets the maximum AGC gain.

Set AGC MAX GAIN to “OFF” and then press the SET

button.

The GAIN SETTING screen will appear. You can use this screen

to set the gain value manually to within a range of 0 – 30 dB.

2 Sets the digital noise reduction.

Note:

• If “OFF” is selected, no maximum gain will be set.

• If “OFF” is selected, the SENSE UP function will be forcibly set

to “OFF”. However, the setting display will not change.

LENS SETTING (LENS)

ꢀ B/W mode setting

D/N SETTING - COLOR

AGC MAX GAIN

DNR

0·

OFF

MAIN MENU

LENS

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

FOCUS

MANU ‚

ZOOM

SET

B/W

OFF

‚

DAY/NIGHT

PRESET

OFF

BACK

MIRROR

VIEW SETTING

OPTION

‚

VIEW ANGLE

PRESET

OFF

BACK

4 ^{DNR setting}

Use the cursor button (j or l) to move the cursor to

DNR, and then use the cursor button (d or c) to select

the digital noise reduction setting (e.g. ON).

1 ^{Use the cursor button (}^j^or^l^{) to select SET for LENS,}

then press the SET button.

The LENS screen will appear.

Available settings:

• ON: DNR (digital noise reduction) is applied. This reduces

interference at low luminance levels.

• OFF: DNR is not applied.

Note:

• Digital noise reduction operates when the gain control

increases. In addition, blurring and ghosting of images can

occur when moving images are being monitored, and so the

resolution is also reduced slightly.

• If AGC MAX GAIN is set to “OFF”, DNR will be forcibly set to

“OFF”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

LENS SETTING (LENS)

D/N SETTING - B/W

AGC MAX GAIN

DNR

+6·

AGC MAX GAIN

DNR

+6·

OFF

BURST

FOCUS

PRESET

OFF

BACK

PRESET

OFF

BACK

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

DAY/NIGHT, use the cursor button (d or c) to select

the level setting (e.g. B/W) and then press the SET

button.

3 ^{AGC MAX GAIN setting}

Use the cursor button (j or l) to move the cursor to

AGC MAX GAIN, and then use the cursor button (d or

c) to select the gain.

The D/N SETTING – B/W screen will appear, and the “+6dB”

setting for “AGC MAX GAIN” will be blinking.

1 Sets the maximum AGC gain.

Available settings: Select the maximum AGC gain from OFF,

–6dB, 0dB, +6dB, +9dB, +12dB or

+15dB.

2 Sets the digital noise reduction.

Setting fixed gain manually

3 Sets burst suppression. If other peripheral devices (such

as a multiplexer) are connected to the system, bursts

(distortion of image color) can occur when switching

between color and black & white. If this happens,

change the BURST setting to “ON”.

Set AGC MAX GAIN to “OFF” and then press the SET

button.

The GAIN SETTING screen will appear. You can use this screen

to set the gain value manually to within a range of 0 – 30 dB.

Note:

4 Sets the focus when switching to black & white mode.

• If “OFF” is selected, no maximum gain will be set.

• If “OFF” is selected, the SENSE UP function will be forcibly set

to “OFF”. However, the setting display will not change.

LENS SETTING (LENS)

D/N SETTING - B/W

5, 6

D/N SETTING - B/W

5 ^{BURST setting}

AGC MAX GAIN

DNR

+6·

AGC MAX GAIN

DNR

+6·

Use the cursor button (j or l) to move the cursor to

BURST, and then use the cursor button (d or c) to

select the burst setting (e.g. ON).

OFF

BURST

FOCUS

Available settings:

PRESET

OFF

BACK

PRESET

OFF

BACK

• ON: The color burst signal is turned on.

• OFF: This should normally be set to “OFF”.

4 ^{DNR setting}

6 ^{FOCUS setting}

Use the cursor button (j or l) to move the cursor to

DNR, and then use the cursor button (d or c) to select

the digital noise reduction setting (e.g. ON).

Use the cursor button (j or l) to move the cursor to

FOCUS, and then use the cursor button (d or c) to

select the focus setting (e.g. 1).

Available settings:

• ON: DNR (digital noise reduction) is applied. This reduces

• 1: Near-infrared wavelength correction is set.

interference at low luminance levels.

(around 900 nm)

• OFF: DNR is not applied.

• 2: Visible light spectrum is set.

Note:

Note: This is set to “1” at the time of shipment from the factory.

• Digital noise reduction operates when the gain control

increases. In addition, blurring and ghosting of images can

occur when moving images are being monitored, and so the

resolution is also reduced slightly.

If the images are out of focus, change it to “2”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• If AGC MAX GAIN is set to “OFF”, DNR will be forcibly set to

“OFF”.

LENS SETTING (LENS)

D VIEW ANGLE setting

ꢀ Day/Night mode operation from the system controller

The VIEW ANGLE setting should normally be left at “OFF”.

The Day/Night setting (AUTO, COLOR and B/W) can be

switched using “CAMERA” operating range of the system

controller. Press the following buttons in the order given to

change the mode setting.

MAIN MENU

LENS

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

FOCUS

MANU ‚

SET

ZOOM

‚

• COLOR mode:

“AUX“ → “AUX” → “1” → “Enter” → “+” button

• B/W mode:

DAY/NIGHT

AUTO ‚

OFF

MIRROR

VIEW SETTING

OPTION

‚

VIEW ANGLE

PRESET

OFF

BACK

“AUX“ → “AUX” → “2” → “Enter” → “+” button

• AUTO mode:

“AUX“ → “AUX” → “3” → “Enter” → “+” button

1 ^{Use the cursor button (j or l) to select SET for LENS,}

then press the SET button.

The LENS screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

VIEW ANGLE, and then use the cursor button (d or c)

to select the setting (e.g. OFF).

Available settings:

• OVER: The image angle for images being monitored is set

to 1.05.

• OFF: This should normally be set to “OFF”.

Note: This should normally be set to “OFF”. However, vignetting

may occur in the corners of the images because of the

zoom position. This is not normally a problem, but if you

are concerned about it, change the setting to “OVER”. The

vignetting will then be less apparent.

MIRROR SETTING

MAIN MENU

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

MIRROR, then use the cursor button (d or c) to select

the mirror image effect (e.g. H).

The image will change as described below each time the

cursor button is pressed.

• OFF: Normal image

• V: Inverted vertically

• H: Inverted horizontally • HV: Inverted horizontally and

vertically

OFF

2 ^{To return to the normal screen, use the cursor button}

(l) to select END at the bottom of the screen, then press

the SET button.

VIEW SETTING ITEM FLOW

A IRIS setting (See p35)

MAIN MENU

This setting allows selection of IRIS to either autoiris (AUTO) or manual iris (MANU). Default setting is

autoiris.

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PRIVACY MASK

LENS

‚

B WHITE BALANCE adjustment (See p42)

MIRROR

Three white balance methods are available: auto trace white balance (ATW), one-push automatic

white balance (AWC), and manual white balance (MWB). Default setting is auto trace white balance.

VIEW SETTING

OPTION

‚

PRESET

C Electronic SHUTTER setting (See p46)

This setting chooses either a fast shutter speed (SHORT) for target objects that may be moving quickly

or a slower shutter speed (LONG) for darker target objects.

VIEW SETTING 1

ꢀ

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

ATW

OFF

‚

D MOTION detector setting (See p48)

APERTURE

GAMMA

‚

This function generates an alarm when a suspicious figure is detected. Each of the settings will enable

certain kinds of detection based on the natural image (swaying trees, flickers of light, etc.). It is also

possible to enable zooming in on target objects and intruders that have unusual brightness levels

(moving, bright) or are fast-moving.

PRESET

OFF

BACK

E Profile compensation setting (APERTURE) (See p54)

This setting emphasizes the target object profile (horizontally or vertically).

ꢀ Setting the VIEW SETTING

Signifies that VIEW

F GAMMA correction setting (See p55)

This setting enables contrast sensitivity to be boosted by controlling the gamma characteristics. Three

gamma controls are available: gamma correction (ON), smart gamma correction 1 (SMART 1), and

smart gamma correction 2 (SMART 2). Default setting is ON.

SETTING 1 is the camera

setting 1. The cursor

button can be used (d or

c) to select one of the

nine VIEW SETTING

patterns (0 – 8).

VIEW SETTING ITEM FLOW

(About creating image setting files in VIEW SETTING)

Note: When each of the following functions is ON (shown by

single circle), it may be possible to use other functions in

conjunction with it (shown by double circle). View columns

vertically to determine which functions can be used

together.

You can set 9 different patterns with view files. Use the cursor

button (d or c) to change the file number (1) for VIEW SETTING

and press the SET button. The selected image setting file will

appear. Neither the mask function nor the motion detector

function can be used with image setting file “0”, so they will not

appear as options in the screen for pattern 0.

IRIS

AUTO: SENSE UP (activated)

MANU: EI (ON)

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

SHUTTER LONG

SHORT

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

ATW

OFF

‚

MOTION

APERTURE

GAMMA

‚

MOTION

MIRROR

VIEW SETTING

OPTION

‚

F: Function is set T: Not allowable E: Allowable

PRESET

OFF

BACK

(Screen for image setting 1 – 8)

VIEW SETTING 0

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

ATW

OFF

---

‚

APERTURE

GAMMA

‚

PRESET

OFF

BACK

(Screen for image setting 0)

VIEW SETTING

A IRIS setting

There are 2 possible settings for IRIS, autoiris (AUTO) and manual iris (MANU).

Autoiris setting (AUTO)

Sets backlight compensation, magnification of electronic

sensitivity and iris level.

VIEW SETTING 1

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

ATW

OFF

‚

APERTURE

GAMMA

‚

PRESET

OFF

BACK

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

2 ^{Press the SET button.}

VIEW SETTING, then press the SET button. (e.g. 1)

The IRIS SETTING screen will appear.

The VIEW SETTING 1 screen will appear and AUTO for IRIS will

be blinking.

Available settings:

• AUTO: Sets automatic adjustment of iris.

• MANU: Sets manual adjustment of iris.

Note:

When AUTO is selected, the following 3 types of detailed

backlight compensation settings will be available.

• Multi-spot evaluative metering (MULT)

• 5 spot centerweighted average metering (CENT)

• 48 multi-spot metering (MASK)

VIEW SETTING

Backlight compensation additional settings 1

IRIS SETTING

BLC SETTING

3 ^{Use the cursor button (j or l) to move the cursor to}

BRIGHT, and then use the cursor button (d or c) to

select the compensation level.

BLC

SENSE UP

MULT ‚

OFF

(BLC WEIGHT)

í------ú------ü

(LEVEL)

í-----ú+------ü 40

(BRIGHT)

í------ú------ü

Available settings: 0 – 15

Note: When the number becomes larger, it brightens, and the

compensation level can be set for the brightness of the

backlighting.

Backlight compensation settings

• MULT (Multi-spot evaluative metering): Evaluates the entire

screen and corrects according to the best image obtained.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• CENT (5 spot centerweighted average metering): Measures

light mainly at the center and corrects according to the best

image obtained. (See p37)

• MASK (48 multi-spot metering): Covers bright areas such as

persons with mask patterns and treats light measurement

output as irrelevant. (See p39)

Note:

• When using multi-spot evaluative metering, the background

behind the target object will become very dark. If a target

image in the center of the image is too bright while using the

multi-spot evaluative metering mode, switch to the 5 spot

centerweighted average metering mode.

• Multi-spot evaluative metering (MULT)

1 ^{Use the cursor button (j or l) to move the cursor to}

BLC, then use the cursor button (d or c) to select a

backlight compensation method. (e.g. MULT) Then press

the SET button.

• If DAY/NIGHT is set to “AUTO” and the images are in black &

white mode, multi-spot evaluative metering will not operate.

The BLC SETTING screen will appear.

2 ^{Use the cursor button (d or c) to select the value of}

BLC WEIGHT. (Sets backlight and brightness level.)

Available settings: 0 – 15

Note: The larger the number, the more backlighting works.

VIEW SETTING

Backlight compensation additional settings 2

• 5 spot centerweighted average metering (CENT)

IRIS SETTING

BLC SETTING

(POSITION)

BLC SETTING

(SIZE)

BLC

SENSE UP

CENT ‚

OFF

(LEVEL)

í-----ú+------ü 40

PRESET

OFF

BACK

1 ^{Use the cursor button (}^d^or^c^{) to select CENT, then}

4 ^{Use the cursor button (}^{j l d c}^{) to adjust the size of}

press the SET button.

the central light sensing zone.

The BLC SETTING (POSITION) screen will appear.

5 ^{Press the SET button.}

2 ^{Use the cursor button (}^{j l d c}^{) to shift the position}

The BLC WINDOW WEIGHTING screen will appear.

of the central light sensing zone.

The zone can be moved up or down and left or right.

Note:

• If the zone fills the right side it will become smaller.

• If the zone fills the bottom side it will become smaller.

3 ^{Press the SET button.}

The BLC SETTING (SIZE) screen will appear.

VIEW SETTING

Example of setting the mask in the center weighting position.

BLC WINDOW WEIGHTING

TOP

BOTTOM

LEFT

BOTTOM

LEFT

BOTTOM

LEFT

BOTTOM

LEFT

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

RIGHT

CENTER(FIX)

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

1 TOP: Weighting is at top.

2 BOTTOM: Weighting is at bottom.

3 LEFT: Weighting is at left.

4 RIGHT: Weighting is at right.

BLC WINDOW WEIGHTING

TOP

BOTTOM

LEFT

5 CENT (FIX): Center weighting is fixed by the number 7.

RIGHT

CENTER(FIX)

If this is set to “0”, the light intensity will be ignored. The larger the setting value, the

greater is the weighting given to light coming from the respective side.

Note:

PRESET

OFF

BACK

6 ^{Use the cursor button (j or l) to select a zone, then}

use the cursor button (d or c) to adjust weighting.

Each setting will change as shown in the illustration.

The area from each of the zones 0 – 7, except CENTER, can

be adjusted.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

Backlight compensation additional settings 3

• 48 multi-spot metering (MASK)

IRIS SETTING

BLC MASKING

BLC

SENSE UP

MASK ‚

OFF

(LEVEL)

í-----ú+------ü 40

CONTINUE (ñ)

PRESET

OFF

BACK

1 ^{Use the cursor button (}^d^or^c^{) to select MASK, then}

3 ^{Finishing mask pattern setting}

press the SET button.

Use the cursor button (j or l) to move a mask pattern to

the bottom area of the screen and continue holding it for 3

seconds. The PRESET and MENU items will appear on the

screen.

The BLC MASKING screen will appear and the mask pattern

will be blinking.

2 ^{Use the cursor button (}^{j l d c}^{) to move the cursor to}

move the mask pattern over the area not to be sensed,

then press the SET button.

• Use the cursor button (l) to select BACK for MENU and

press the SET button. The IRIS SETTING screen will

reappear.

The mask pattern will be set. You can use the same steps to

set additional mask patterns.

• Use the cursor button (l) to move the cursor to BACK for

MENU, use the cursor button (d or c) to select END, and

then press the SET button. The normal screen will reappear.

Note: The initial mask pattern is at the upper left of the screen,

and it is not set. To clear a mask pattern after it is set,

press the SET button again.

VIEW SETTING

SENSE UP setting

LEVEL setting

IRIS SETTING

MULT

IRIS SETTING

BLC

SENSE UP

MULT

BLC

SENSE UP

(LEVEL)

í----ú-+------ü 40

(LEVEL)

í-----ú+------ü 40

PRESET

OFF

BACK

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to

LEVEL, then use the cursor button (d or c) to adjust the iris

level.

Use the cursor button (j or l) to move the cursor to

SENSE UP, then use the cursor button (d or c) to select the

power of the electronic sensitivity. (e.g. x4)

Available settings: 0 – 100

Available settings: OFF, x2, x4, x8, x16, x32

Note: The larger the number, the more it brightens.

Note:

• Electronic sensitivity boosting (SENSE UP) automatically

lengthens the CCD exposure time in dark situations.

Accordingly, do not use for light target objects. Because

exposure time is lengthened while in operation, moving target

objects may cause conspicuous afterimages and blurs.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• It is not possible to set SENSE UP (activated) or SHUTTER

(LONG) when MOTION is set to “ON”.

• When SENSE UP is activated for IRIS SETTING, the electronic

shutter cannot be forcibly moved.

• If DAY/NIGHT is set to “AUTO” and the images are in color

mode, electronic sensitivity boosting will not operate.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

Manual iris setting

Sets electronic iris ON/OFF, lens aperture and iris level.

MAIN MENU

VIEW SETTING 1

IRIS SETTING

LANGUAGE

CAMERA ID

SYNC

PRIVACY MASK

LENS

SET

OFF

INT

SET

OFF

‚

IRIS

MANU ‚

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

OFF

(IRIS STOP)

í------+------ú 17

(IRIS STOP)

í------+------ú 17

‚

APERTURE

GAMMA

‚

MIRROR

(LEVEL)

í----ú-+------ü 40

(LEVEL)

í----ú-+------ü 40

VIEW SETTING

OPTION

‚

SET

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

LEVEL, then use the cursor button (d or c) to select the

value.

VIEW SETTING, then press the SET button. (e.g. 1)

The VIEW SETTING 1 screen will appear.

Available settings: 0 – 100 (Level of opening)

2 ^{Use the cursor button (}^d^or^c^{) to select MANU, then}

press the SET button.

Note:

The IRIS SETTING screen will appear.

• The smaller the value the more the video level drops,

becoming darker.

3 ^{Electronic IRIS setting}

• The LEVEL setting controls both AGC circuit gain and shutter

speed, changing the amount of exposure.

Use the cursor button (d or c) to select El. (e.g. ON)

Note: When SENSE UP is activated for IRIS SETTING, the

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

electronic shutter cannot be forcibly moved.

4 ^{Lens aperture setting}

Use the cursor button (j or l) to move the cursor to IRIS

Note:

STOP, then use the cursor button (d or c) to select the value.

• If the iris views an unusually bright image, it can cause a

smear that cannot be corrected by adjusting the light entering

through the lens. In this case, arrange the physical angle of

lighting in a way that will prevent on-screen smearing.

Available settings: 1 – 17 (Aperture opening)

Note:

• The smaller the value the more the aperture closes and the

image darkens.

• If flickering of the target object occurs because of florescent

lighting in the camera location, changing to incandescent

lighting will prevent the flickering.

• Changes to the value directly control the aperture of the lens.

VIEW SETTING

B WHITE BALANCE adjustment

Adjustments can be made to 3 methods of white balance correction: Auto trace white balance (ATW), one-push automatic white balance

(AWC), and manual white balance (MWB).

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

MWB

OFF

‚

PRIVACY MASK

LENS

‚

MOTION

APERTURE

GAMMA

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

The following methods are available for white balance correction.

See the corresponding reference sections for additional setting

options.

1 ^{Use the cursor button (j or l) to move the cursor to}

VIEW SETTING, then press the SET button. (e.g. 1)

The VIEW SETTING 1 screen will appear.

Available methods:

2 ^{Use the cursor button (j or l) to move the cursor to}

WHITE BALANCE, then use the cursor button (d or c)

to select a white balance type “MWB”. Then press the

SET button.

ATW (Auto trace white balance)

Even when light sources change, automatic adjustment assures

capture of most suitable colors. When a bright light source

prevents effective white balance, a mask can be placed over the

light source. (See p43)

The MWB SETTING screen will appear.

AWC (One-push automatic white balance)

White balance is adjusted automatically with one-push activation.

AWC is usually set for white target objects (walls, paper, etc.) that

do not return color faithfully in the ATW method. (See p45)

MWB (Manual white balance)

Fine adjustments for preferred colors can be done manually. This

method is preferable when suitable colors cannot be obtained

with the ATW method. (See p43)

VIEW SETTING

White balance additional settings 1

MWB setting

White balance additional settings 2

ATW setting

Automatic white balance settings are completed when ATW is

selected. However, white balance will not be suitably adjusted if a

bright light source or an excessively dark area from the

environment is in the image. In this case, the bright light source or

dark area should be masked so that it will not be detected.

VIEW SETTING 1

MWB SETTING

(OFFSET)

IRIS

AUTO ‚

WHITE BALANCE

SHUTTER

MOTION

MWB

‚

LONG ‚

OFF

R í---ú--+------ü 70

B í---ú--+------ü 66

APERTURE

GAMMA

‚

VIEW SETTING 1

AUTO ‚

ATW SETTING

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

WHITE BALANCE, then use the cursor button (d or c)

to select a white balance type (e.g. MWB). Then press

the SET button.

IRIS

MASKING

SMART ATW

‚

WHITE BALANCE

SHUTTER

ATW

OFF

‚

OFF

MOTION

APERTURE

GAMMA

‚

The MWB SETTING screen will appear.

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

2 ^{Use the cursor button (}^d^or^c^{) to adjust the value for}

ATW for WHITE BALANCE and press the SET button.

“R” (red).

The ATW SETTING screen will appear.

Available settings: 0 – 255

2 ^{Use the cursor button (}^d^or^c^{) to select ON for}

Note: The larger the number, the stronger red becomes.

MASKING, then press the SET button.

3 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

“B”, then use the cursor button (d or c) to adjust the

“Blue” value.

The ATW MASKING screen will appear with the mask pattern

blinking in the upper left corner of the screen.

Available settings: 0 – 255

Note: The larger the number, the stronger blue becomes.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

ATW MASKING

ATW SETTING

MASKING

‚

MASKING

‚

SMART ATW

OFF

SMART ATW

CONTINUE (ñ)

PRESET

OFF

BACK

PRESET

OFF

BACK

ꢀ SMART ATW setting

If saturation is high or a scene is bright, the most suitable colors

may not be obtained. In this case, set the SMART ATW to ON.

3 ^{Use the cursor button (}^{j l d c}^{) to move the mask}

pattern over the bright light source, then press the SET

button.

Use the same steps to place addition masks as needed.

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SMART ATW, then use the cursor button (d or c) to set

ON.

Note: Initial settings place no masks on the screen. To cancel the

placement of masks, press the SET button again.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

4 ^{Use the cursor button (}^j^or^l^{) to move a mask pattern}

to the bottom area of the screen and continue holding

the cursor button straight down for 3 seconds.

The PRESET and MENU items will appear on the screen. Use

the cursor button (j or l) to select BACK, then press the

SET button. The ATW SETTING screen will reappear.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

White balance additional settings 3

AWC setting

VIEW SETTING 1

AWC SETTING

MWB SETTING

(OFFSET)

IRIS

AUTO ‚

AWC LOCK

GO TO MWB

SET

AWC LOCK

GO TO MWB

SET

WHITE BALANCE

SHUTTER

MOTION

AWC

OFF

‚

R í---ú--+------ü 70

B í---ú--+------ü 66

APERTURE

GAMMA

‚

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

3 ^{GO TO MWB setting}

AWC for WHITE BALANCE and press the SET button.

Use the cursor button (j or l) to move the cursor to

The AWC SETTING screen will appear.

SET for GO TO MWB and press the SET button.

The MWB SETTING screen will appear and the “R” value will

be blinking.

2 ^{With SET blinking for AWC LOCK, press the SET button.}

SET will light and adjustment of white balance will begin. After

about 3 seconds, SET will begin blinking again, signaling that

adjustment is complete.

4 ^{Use the cursor button (}^d^or^c^{) to adjust the value for}

“R” (red).

Available settings: 0 – 255

Note:

Note: The larger the number, the stronger red becomes.

For even finer adjustment of coloration, choose SET for GO TO

MWB. White balance mode will become MWB for fine

adjustment. After fine adjustment with GO TO MWB, the white

balance mode will automatically switch to MWB.

5 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

“B”, then use the cursor button (d or c) to adjust the

“Blue” value.

Note: Full adjustment may not be possible with just one

activation of SET for AWC LOCK. In that case, press the

SET button again.

Available settings: 0 – 255

Note: The larger the number, the stronger blue becomes.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

C Electronic SHUTTER setting

Sets the electronic shutter to either the fast shutter speed mode (SHORT) or the slow shutter speed mode (LONG).

Fast shutter speed (SHORT) mode setting

MAIN MENU

VIEW SETTING 1

MANU ‚

ES SETTING

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

IRIS

SHUTTER SPEED

WHITE BALANCE

SHUTTER

ATW

‚

SHORT‚

OFF

PRIVACY MASK

LENS

‚

MOTION

APERTURE

GAMMA

‚

MIRROR

OFF

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{Use the cursor button (d or c) to select a electronic}

VIEW SETTING, then press the SET button. (e.g. 1)

shutter speed.

The VIEW SETTING 1 screen will appear.

Available settings: 60, 100, 250, 500, 1000, 2000, 4000,

10000

2 ^{Use the cursor button (j or l) to move the cursor to}

SHUTTER, then use the cursor button (d or c) to select

the speed mode for the electronic shutter. (e.g. SHORT)

Then press the SET button.

Note: SHORT mode cannot be set if SENSE UP is activated or IRIS

is “ON”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

The ES SETTING screen will appear and 60 (1/60 sec) will be

blinking. This setting is suitable for fast moving target objects.

VIEW SETTING

Slow shutter speed (LONG) mode setting

VIEW SETTING 1

ES SETTING

IRIS

MANU ‚

SHUTTER SPEED

WHITE BALANCE

SHUTTER

MOTION

ATW

‚

LONG ‚

OFF

APERTURE

GAMMA

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

Note:

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SHUTTER, then use the cursor button (d or c) to select

the speed mode for the electronic shutter. (e.g. LONG)

Then press the SET button.

SHUTTER (LONG) cannot be set if any of the following settings is

active.

• MOTION: ON

The ES SETTING screen will appear and x1 (1/60 sec) will be

blinking. This setting is suitable for dark target objects.

• IRIS: AUTO item SENSE UP (activated) or MANU item El

(ON)

Note: When setting the electronic shutter, the ELS button on the

system controller can only be used to turn the electronic

shutter on and off.

2 ^{Use the cursor button (}^d^or^c^{) to select a electronic}

shutter speed.

Available settings: x1, x2, x4, x8, x16, x32 (Field times

shown as multiples.)

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

D MOTION detector setting

This function divides the monitor screen into 48 zones (8 x 6). Based on information from the separate zones, target images tha t show

intruder movements are detected and an alarm is generated. The degree of motion to be detected can be finely set.

Note:

• Before activating this setting, use the cursor button to select a surveillance location that will not detect motion.

• When SHUTTER speed is in LONG mode and IRIS SETTING has SENSE UP activated, the MOTION function cannot be turned ON.

MAIN MENU

VIEW SETTING 1

MANU ‚

MOTION SETTING

MOTION SIZE

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

IRIS

SIZE

SET

‚

WHITE BALANCE

SHUTTER

ATW

‚

MASKING

SENSITIVITY

ZOOM

LONG ‚

SET

OFF

PRIVACY MASK

LENS

‚

MOTION

APERTURE

GAMMA

‚

INTERVAL

ALARM SIGN

MIRROR

OFF

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{MOTION SIZE setting}

VIEW SETTING, then press the SET button. (e.g. 1)

Sets the target object size desired for detection in the 48 zone

screen.

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

MOTION, and then use the cursor button (d or c) to

select ON. Then press the SET button.

Press the SET button again.

The MOTION SIZE screen appears and the “1” for “V” will be

blinking.

The MOTION SETTING screen will appear and SET for SIZE will

be blinking.

VIEW SETTING

MOTION SIZE

4 ^{Set the size of the target object desired for detection}

1 Determine the vertical size

Tilt the cursor button to the right (c).

PRESET

OFF

PRESET

OFF

PRESET

OFF

BACK

The “V” value (vertical pattern) will change to “2” and the

detection pattern will expand downward. Repeating this

motion will expand the pattern in the up and down

direction. Tilting the cursor button to the left will reduce

the pattern size.

V1, H1

V2, H1

V6, H1

MOTION SIZE

2 Determine the horizontal size

PRESET

OFF

PRESET

OFF

PRESET

OFF

Use the cursor button (l) to move the cursor to the

“1” for “H”, then tilt the cursor button to the right

(c).

BACK

V2, H2

V2, H3

V3, H3

MOTION SIZE

The “H” value (horizontal pattern) will change to “2” and the

detection pattern will expand to the left. Repeating this

motion will expand the pattern in the left and right direction.

Tilting the cursor button to the left will reduce the pattern

size.

PRESET

OFF

BACK

PRESET

OFF

BACK

PRESET

OFF

BACK

V1, H2

V1, H3

V1, H8

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

MOTION MASKING setting

Masking target objects that are not desired for detection (swaying trees, flickers of light , etc.) will prevent unwanted alarms from being

generated. This is done in the MOTION SETTING screen.

MOTION SETTING

MOTION MASKING

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

SET

OFF

INTERVAL

ALARM SIGN

OFF

CONTINUE (ñ)

PRESET

OFF

BACK

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

MASKING, and then use the cursor button (d or c) to

select ON. Then press the SET button.

3 ^{Finishing motion pattern setting}

Use the cursor button (j or l) to move a mask pattern to

the bottom area of the screen and continue holding it for 3

seconds. The PRESET and MENU items will appear on the

screen.

The MOTION MASKING screen will appear, and the mask

pattern will be blinking in the upper left corner of the screen.

2 ^{Use the cursor button (}^{j l d c}^{) to move the mask}

pattern to the target object that is not to be detected,

then press the SET button.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Repeat these steps to set mask patterns in other locations.

Note: To clear a mask pattern, press the SET button again on

the pattern.

VIEW SETTING

When noise from a dark screen is causing erroneous detections,

make the value larger.

SENSITIVITY setting

Set the degree of sensitivity for motion detection corresponding

to MOTION SIZE. Sensitivity can be set so that natural motions on

the screen such as wind and light changes will not be detected.

When this is necessary, activate the following setting.

Available settings: 1 – 10

ꢀ Brightness differences (Y-DIFFER)

Use the cursor button (j or l) to move the cursor to

Y-DIFFER, then use the cursor button (d or c) to adjust the

brightness differences.

MOTION SETTING

SENSITIVITY

í---ú----ü

Y-LEVEL í---ú----ü

Y-DIFFER í---ú----ü

DURATION ú--------ü

SIZE

SET

‚

MOVE

MASKING

SENSITIVITY

ZOOM

SET

OFF

Changes in brightness can sometimes be mistakenly detected as

motion. To avoid detection of the turning on and off of lighting,

make the value larger.

INTERVAL

ALARM SIGN

OFF

DEMO

OFF

Available settings: 1 – 10

Use the cursor button (j or l) to move the cursor to

SENSITIVITY, and then use the cursor button (d or c) to

ꢀ DURATION setting

select SET. Then press the SET button.

Use the cursor button (j or l) to move the cursor to

DURATION, then use the cursor button (d or c) to adjust

the detection time duration.

The SENSITIVITY screen will appear.

When necessary, adjust the following settings.

To avoid detecting fast movements, make the value larger.

ꢀ Motion sensitivity (MOVE) setting

Available settings: 1 – 60

Use the cursor button (j or l) to move the cursor to

MOVE, then use the cursor button (d or c) to adjust the

movement value.

ꢀ Detected motion confirmation mode (DEMO)

Use the cursor button (j or l) to move the cursor to OFF for

DEMO, then use the cursor button (d or c) to change ON.

To avoid detection of small movements such as wind, make the

value larger.

When a motion is detected, patterns are shown in that location.

While the detected motion is being confirmed, the SENSITIVITY

settings are optimized. This mode can only be activated in the

SENSITIVITY setting screen.

Available settings: 1 – 10

ꢀ Brightness level (Y-LEVEL)

Use the cursor button (j or l) to move the cursor to

Y-LEVEL, then use the cursor button (d or c) to adjust the

brightness level.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

ZOOM setting

INTERVAL setting

This item is set in the MOTION SETTING screen.

MOTION SETTING

SIZE

SET

‚

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

MASKING

SENSITIVITY

ZOOM

SET

OFF

SET

OFF

INTERVAL

ALARM SIGN

INTERVAL

ALARM SIGN

OFF

PRESET

OFF

BACK

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to

INTERVAL, then use the cursor button (d or c) to select the

time interval (e.g. 15S).

Use the cursor button (j or l) to move the cursor to

ZOOM, then use the cursor button (d or c) to select the

zoom magnification power (e.g. x2).

Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,

Available settings: OFF, x1.4, x2, x2.8, x4, x6

Note:

Note: When a motion is detected, no other motions will be

• When a suspicious motion is detected, the camera zooms in

according to the set magnification power. The zoom takes

effect for 5 seconds and then returns to the previous

magnification level.

detected within the set interval of time.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

• The zoom focuses on the center of the screen. If the

maximum optical performance is exceeded, zooming will stop

at maximum magnification.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

ALARM SIGN setting

This item is set in the MOTION SETTING screen.

MOTION SETTING

SIZE

SET

‚

MASKING

SENSITIVITY

ZOOM

SET

OFF

INTERVAL

ALARM SIGN

OFF

PRESET

OFF

BACK

Use the cursor button (j or l) to move the cursor to OFF

for ALARM SIGN, and then use the cursor button (d or c)

to select ON.

Available settings:

• ON: The camera ID display blinks when motion is detected.

• OFF: The camera ID display does not blink when motion is

detected.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

E Profile compensation setting (APERTURE)

Set this function to further emphasize the profile of the target object. The amount of compensation can be adjusted for horizontal or

vertical directions.

MAIN MENU

VIEW SETTING 1

AUTO ‚

APERTURE SETTING

H í------ú------ü

V í------ú------ü

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

IRIS

WHITE BALANCE

SHUTTER

ATW

OFF

‚

PRIVACY MASK

LENS

‚

MOTION

APERTURE

GAMMA

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

3 ^{Select the amount of profile compensation}

Available settings: 1 – 15 (Compensation intensity)

1 Set the horizontal profile compensation

VIEW SETTING, then press the SET button. (e.g. 1)

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

APERTURE and then use the cursor button (d or c) to

select ON. Then press the SET button.

Use the cursor button (d or c) to adjust the value for

“H” (horizontal).

2 Set the vertical profile compensation

The APERTURE SETTING screen will appear and the “H” value

will be blinking.

Use the cursor button (j or l) to move the cursor to “V”

(vertical), then use the cursor button (d or c) to adjust

the value for “V”.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

VIEW SETTING

F GAMMA correction setting

In addition to turning gamma correction ON or OFF, contrast sensitivity can be boosted at 2 levels.

MAIN MENU

VIEW SETTING 1

IRIS AUTO ‚

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

WHITE BALANCE

SHUTTER

ATW

OFF

‚

PRIVACY MASK

LENS

‚

MOTION

APERTURE

GAMMA

‚

MIRROR

VIEW SETTING

OPTION

‚

PRESET

OFF

BACK

1 ^{Use the cursor button (j or l) to move the cursor to}

VIEW SETTING, then press the SET button. (e.g. 1)

The VIEW SETTING 1 screen will appear.

2 ^{Use the cursor button (j or l) to move the cursor to}

ON for GAMMA, then use the cursor button (d or c) to

select the gamma correction.

Available settings:

• OFF: No gamma correction

• ON: Gamma correction (γ = 0.45)

• SMART 1: Correction 1

• SMART 2: Correction 2 (improves contrast for dark

locations)

Note: When using SMART 1 or SMART 2, the target object may

be too bright, so determine which setting is better for the

target object.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

OPTION SETTING

MAIN MENU

OPTION

RS-485 SETTING

BAUD RATE

RS-485 SETTING

BAUD RATE

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

19200

OFF

19200

OFF

TERMINATE

PRIVACY MASK

LENS

‚

MIRROR

VIEW SETTING

OPTION

‚

SET

ꢀ Option settings

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

485 for CONTROL, use the cursor button (d or c) to

select the device to be operated (e.g. 485), and then

press the SET button.

• CONTROL setting: This sets whether other peripheral devices

can be used to operate the camera by means of the RS-485

interface or a linked coaxial cable.

• ADDRESS setting: Use this to set the address for this camera

when more than one camera is connected or when other

peripheral devices or a system controller have been connected.

(See p57)

The RS-485 SETTING screen will appear.

Available settings:

• 485: For operation by the System Controller

• COAX: For operation of device by linked coax cable.

• ALARM setting: This is used for settings related to alarm

input and alarm output. In addition, it is also used to force

selection of COLOR mode or B/W mode when the

3 ^{Use the cursor button (}^d^or^c^{) to select 19200 for BAUD}

RATE.

DAY/NIGHT setting function is being used. (See p57)

Available settings: 19200, 9600, 4800, 2400

4 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

TERMINATE, and then use the cursor button (d or c) to

select the terminate setting.

CONTROL setting

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

SET for OPTION, then press the SET button.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

The OPTION screen will appear.

Note: The PRESET ON setting cannot be used when OPTION

settings are in use.

OPTION SETTING

ALARM setting

MAIN MENU

OPTION

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

A Alarm input setting (ALARM IN)

Make the following settings for alarm detection.

PRIVACY MASK

LENS

‚

MIRROR

Connect the external alarm switch to the alarm input terminal on

the back of the camera.

VIEW SETTING

OPTION

‚

SET

ADDRESS setting

MAIN MENU

OPTION

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

‚

CONTROL

ADDRESS

ALARM

485

SET

‚

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

PRIVACY MASK

LENS

‚

SET for OPTION, then press the SET button.

MIRROR

The OPTION screen will appear.

VIEW SETTING

OPTION

‚

SET

Note: The PRESET ON setting cannot be used when OPTION

1 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

settings are in use.

SET for OPTION, then press the SET button.

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ADDRESS, and then use the cursor button (d or c) to

select the address.

The OPTION screen will appear.

Note: The PRESET ON setting cannot be used when OPTION

settings are in use.

Available settings: 0 (d) – 127 (c)

2 ^{Use the cursor button (}^j^or^l^{) to move the cursor to}

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

SET for ALARM, then press the SET button.

The ALARM SETTING screen will appear.

3 ^{Alarm input setting}

Use the cursor button (j or l) to move the cursor to

ALM for ALARM IN, and then use the cursor button (d

or c) to set the input (e.g. ALM).

OPTION SETTING

ALARM SETTING

3, 4

ALARM IN

POLARITY

MOTION

ALM

DURATION

OFF

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

OFF

ALARM OUT

ALARM TIME

OFF

1 External alarm input

4 ^{POLARITY setting}

2 Motion sensor detection

Use the cursor button (j or l) to move the cursor to

POLARITY, then use the cursor button (d or c) to select

“NO” or “NC”.

• OR: Outputs an alarm if either an external alarm or a

motion sensor alarm is detected.

6 ^{Alarm duration setting (DURATION)}

Available settings:

Use the cursor button (j or l) to move the cursor to

DURATION, then use the cursor button (d or c) to

select the alarm duration.

• NO: Normal open (Normally open so closed condition is

detected as input.)

• NC: Normal closed (Normally closed so open condition is

Set the duration for the following alarm input reception.

detected as input.)

Available settings: 5S (default setting), 10S, 15S, 20S, 30S,

5 ^{Motion sensor input setting (MOTION)}

1M, 2M, 3M, 4M, 5M

Use the cursor button (j or l) to move the cursor to

MOTION, then use the cursor button (d or c) to select

the input.

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

Matches information from the camera’s motion sensor and

the external alarm and outputs it.

Available settings:

• OFF: Does not output a motion sensor alarm.

• AND: Outputs an alarm when an external alarm input and

motion sensor alarm are detected at the same time.

OPTION SETTING

B Color/black & white selection setting (DAY/NIGHT)

3 ^{POLARITY setting}

The ALARM IN terminal on the rear panel can be used to force

the image mode to color mode or black & white mode. Use this

setting when using this terminal to force the mode selection.

However, when this setting is being used, external alarm input

cannot be received.

Use the cursor button (j or l) to move the cursor to

POLARITY, then use the cursor button (d or c) to select

“NO” or “NC”.

Available settings:

• NO: Normally open (Normally open, and mode switches

between color and black & white when closed)

LENS

2, 3

ALARM SETTING

• NC: Normally closed (Normally closed, and mode switches

FOCUS

MANU ‚

SET

ALARM IN

POLARITY

MOTION

ALM

between color and black & white when opened)

ZOOM

‚

OFF

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

PRESET

DAY/NIGHT

COLOR‚

OFF

Between ALARM

IN - COM terminals

Mode after

selection

POLARITY setting

VIEW ANGLE

OFF

BACK

PRESET

OFF

BACK

When set to NO Open

COLOR

Closed

B/W

1 ^{Set DAY/NIGHT in the LENS setting screen to “COLOR”.}

When set to NC

Open

COLOR

B/W

First change the DAY/NIGHT setting in the LENS setting screen

to “COLOR”. (See p23)

Closed

2 ^{Color/black & white selection setting}

Note:

Use the cursor button (j or l) to move the cursor to

ALM for ALARM IN, and then use the cursor button (d

or c) to set the input (e.g. COLOR).

• If DAY/NIGHT has been set to “COLOR”, color/black &

white selection will not be possible.

• If COLOR is selected, settings relating to external alarm

input will not be displayed, and it will not be possible to

receive external alarm inputs.

• ALM: The control terminal (ALARM IN) is used for alarm input.

• COLOR: The control terminal (ALARM IN) is used for

color/black & white selection input. External operations can

then be used to forcibly switch the mode to color mode or

black & white mode.

• The color/black & white selection setting is applied from the

point after the menu is exited.

OPTION SETTING

C Alarm output setting (ALARM OUT)

ALARM SETTING

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ALM

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ALM

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ALM

OFF

1 ^{ALARM OUT setting}

3 ^{ALARM TIME setting}

Use the cursor button (j or l) to move the cursor to

ALARM OUT, then use the cursor button (d or c) to

select “ON” or “ OFF”.

Use the cursor button (j or l) to move the cursor to

ALARM TIME, then use the cursor button (d or c) to

select the amount of time for external alarm output.

Available settings:

Available settings: 5S, 10S, 15S, 20S, 30S, 1M, 2M, 3M, 4M,

• ON: Output an alarm (for activation of buzzer or lamp)

• OFF: Does not output an alarm

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

2 ^{POLARITY setting}

Use the cursor button (j or l) to move the cursor to

POLARITY, then use the cursor button (d or c) to select

“NO” or “NC”.

Available settings:

• NO: Normal open (Normally open so closed condition is

detected as input.)

• NC: Normal closed (Normally closed so open condition is

detected as input.)

OPTION SETTING

D Operation of alarm signal output to the System

Controller setting (LINE OUT)

Outputs alarm signal to the System Controller. The ALARM lamp

on the System Controller will blink when it receives an alarm

signal. An alarm list can be displayed to show information such as

date/time alarm was received, the device sending the alarm and

the alarm type.

ALARM SETTING

ALARM IN

POLARITY

MOTION

ALM

OFF

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

OFF

Use the cursor button (j or l) to move the cursor to LINE

OUT, then use the cursor button (d or c) to select “ON” or

“OFF”.

Available settings:

• ON: Outputs alarm signal to the System Controller

• OFF: Does not output alarm signal to the System Controller

ꢀ To close the menu screen or return to the previous

screen, select BACK or END for MENU and press the SET

button.

MENU FLOW

LANGUAGE

CAMERA ID SETTING

L-L SETTING

(V SYNC PHASE)

ú------+------ü

LANGUAGE

LANGUE

ENGLISH

FRENCH

SPANISH

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0123456789 :-‚

IDIOMA

ID ????????????????

POSITION

SET

‚

BACK

PASSWORD

(NEW PASSWORD)

1234

SET ‚

****

SET ‚

MAIN MENU

PRIVACY MASK SETTING

PASSWORD LOCK ON ‚

LANGUAGE

CAMERA ID

SYNC

SET

OFF

INT

SET

OFF

SET

OFF

END

‚

PASSWORD CHANGE SET ‚

MASK SET SET ‚

PASSWORD

PRIVACY MASK

LENS

‚

MIRROR

(NOW PASSWORD)

MASK 3 SET

(POSITION)

VIEW SETTING

OPTION

‚

****

SET ‚

PRESET

BACK

MASK NO.SELECT

MASK

OFF

SET

‚

OFF

OPTION

CONTROL

ADDRESS

ALARM

485

SET

‚

LENS

FOCUS SETTING

AREA SETTING

FOCUS

MANU ‚

LIMIT NEAR

SENSITIVITY

AREA

RS-485 SETTING

HIGH

SET

ZOOM

SET

‚

BAUD RATE

TERMINATE

19200

OFF

MANU

DAY/NIGHT

AUTO ‚

OFF

VIEW ANGLE

PRESET

OFF

BACK

ZOOM SETTING

FOCUS SETTING

LIMIT NEAR 1M

PRESET

OFF

BACK

SPEED

EL ZOOM

V-RESO.UP

OFF

SPEED

ALARM SETTING

ALARM IN

POLARITY

MOTION

DURATION

ALARM OUT

POLARITY

ALARM TIME

LINE OUT

ALM

AUTO, COLOR, B/W

OFF, ON

OFF

See page 63

OFF

MENU FLOW

CENT

MASK

BLC MASKING

VIEW SETTING 1

IRIS SETTING

BLC SETTING

(POSITION)

IRIS

AUTO ‚

BLC

SENSE UP

OFF

(BLC WEIGHT)

í------ú------ü

WHITE BALANCE

SHUTTER

MOTION

ATW

OFF

‚

(LEVEL)

(BRIGHT)

í------ú------ü

MULT

APERTURE

GAMMA

‚

í------ú------ü 40

CONTINUE (ñ)

PRESET

OFF

BACK

IRIS SETTING

OFF

(IRIS STOP)

í------ú------ü 17

MANU

BLC SETTING

(SIZE)

BLC WINDOW WEIGHTING

(LEVEL)

í------ú------ü 60

TOP

BOTTOM

LEFT

RIGHT

CENTER(FIX)

PRESET

OFF

BACK

ATW SETTING

AWC SETTING

MWB SETTING

(OFFSET)

MASKING

OFF

AWC LOCK

GO TO MWB

SET

SMART ATW

‚

R í---ú--+------ü 70

B í---ú--+------ü 66

ES SETTING

SHUTTER SPEED

SHORT

LONG

SHUTTER SPEED

MOTION SETTING

MOTION SIZE

MOTION MASKING

SENSITIVITY

í---ú----ü

Y-LEVEL í---ú----ü

Y-DIFFER í---ú----ü

DURATION ú--------ü

SIZE

SET

OFF

‚

MOVE

MASKING

SENSITIVITY

ZOOM

INTERVAL

ALARM SIGN

OFF

DEMO

OFF

PRESET

OFF

BACK

CONTINUE (ñ)

PRESET

OFF

BACK

APERTURE SETTING

H í------ú------ü

V í------ú------ü

SPECIFICATIONS

Pickup device

Effective pixels

Horizontal resolution

Lens

: 1/4"

: 768 (H) x 494 (V)

: Over 520 TV lines

: x22 zoom lens, f=3.6 – 79.2mm (F1.6 – 3.8)

Electronic zoom and gearing

Motion detector

Privacy masking

: ON/OFF, ON allows setting of detection

patterns on a 48 zone screen for 6 motion

settings (size, masking, sensitivity, zoom,

interval, alarm sign)

: ON/OFF, max of 4 masked locations

Password lock possible

Zoom speed setting possible

Alarm input/output

(back panel control

terminals)

Electronic zoom

: 16 power (combined with optic zoom gives

352 power max)

Max zoom magnification setting possible

Vertical resolution ON/OFF setting

: AUTO/MANUAL

AF area setting possible (3 step)

: Alarm input: 1 (for external alarm switch)

Alarm output: 1 (for sending a signal to the

system controller or an alarm detection

device such as a buzzer)

Autofocus

Iris control

Mirror image effect

: Horizontally (H), vertically (V), horizontally

and vertically (HV)

: AUTO/MANUAL, 1/2 EV steps

Synchronization method : Internal synchronization/Line lock,

Camera ID

View settings

: ON/OFF, 16 characters

: 9 (0 – 8) screen files can be established, and

each file can set 7 capturing characteristics

such as iris

V phase adjustment possible

Lowest image illumination: 1.2 lx (F1.6, AGC gain at maximum, COLOR

mode)

0.06 lx (F1.6, B/W mode)

0.04 lx (F1.6, x32 electronic sensitivity

increased, COLOR mode)

Communications

Operational

temperature/humidity

Power source

Power consumption

Weight

: Coaxial control, RS-485

: –10 – +50°C/below 90% RH

: 24 V AC, 60 Hz/12 – 15 V DC

: 4.5 W

0.002 lx (F1.6, x32 SENSE UP, B/W mode)

S/N

Backlight compensation : Multi-spot evaluative metering

5 spot centerweighted average metering

: Over 48dB

: 380 g

48 multi-spot metering

Day/Night

Electronic shutter

: AUTO / COLOR / B/W settings available

SERVICE

• ^{Fast shutter speed mode (SHORT);}

1/60, 1/100, 1/250, 1/500, 1/1000,

1/2000, 1/4000, 1/10000

This camera is a precision instruments and if treated with care,

will provide years of satisfactory performance. However, in the

event of a problem, the owner is advised not to attempt to make

repairs or open the cabinet. Servicing should always be referred to

your dealer or Sanyo Authorized Service Centre.

• ^{Slow shutter speed mode (LONG);}

x1, x2, x4, x8, x16, x32

Electronic sensitivity

boosting

: AUTO/OFF, works with auto iris

Up to x32 max setting possible

White balance

AGC gain

: ATW/AWC/MWB

: OFF/–6/ 0/+6/+9/+12/+15dB

SPECIFICATIONS

MAIN FEATURES

Dimensions

• Built in Interline transfer method 1/4” CCD, approx. 410,000

picture elements.

54 mm

6 mm

125.3 mm

116 mm

• High sensitivity, minimum required illumination is 1.2 lux.

(F1.6, gain max)

9.3 mm

• More than 520 TV lines of horizontal resolution.

• Equipped with intelligent Backlight compensation.

• Special Gamma mode (contrast up)

• Built in high speed electronic shutter and slow shutter.

• 32X Electronic sensitivity

• Built in Digital Motion Detection

• Built in Privacy masking function

1/4"-20UNC

• 12VDC/24V AC dual operation(electrically isolate) .

• Internal sync. / Line Lock.

External appearance and specifications subject to change

without notice.

• 22x optical zoom and 16x electronic zoom.

• Coaxial control or RS485, operation via SSP.

• The Day/Night function is a function that can adapt to a wide

range of changing luminance levels by automatically switching

to color during daytime, or to black and white at times of low

luminance such as nighttime.

SANYO INDUSTRIAL VIDEO

COLOR VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and

addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.

For product operation, authorized service center referral, service assistance or problem resolution, call

CUSTOMER INFORMATION 1-800-421-5013

Weekdays 8:30 AM – 5:00 PM Pacific Time

For accessories and/or parts, call

PARTS ORDER INFORMATION 1-800-726-9662

Weekdays 8:30 AM – 5:00 PM Pacific Time

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES AND PROTECTORATES. THIS WARRANTY APPLIES

ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER

AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or

replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.

LABOR

3 YEARS

PARTS

3 YEARS

IMAGE DEVICE

3 YEARS

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced

or removed.

This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized

service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,

flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.

SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE

FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS

WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC’S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH

THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR’S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT,

SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No._____________________________________________________________________

Date of Purchase _______________________________________________________________

Serial No. _____________________________________________________________________

(Located on back or bottom side of unit.)

Purchase Price _________________________________________________________________

Where Purchased _________________________________________________________________________________________________________________________________________________

Printed on recycled paper

Imprimé sur du papier recyclé

Impreso en papel reciclado

SANYO Electric Co., Ltd.

1AC6P1P2630--

Printed in Japan

L5AD2/US(1202KP-CZ)a

Radio Shack Clock Radio 12 1632 User Guide
Rival Can Opener CN738 User Guide
Roberts Radio Radio RD 59 User Guide
Roland Printer SJ 645EX User Guide
Rover Lawn Mower ProCut 50 User Guide
Samsung Cable Box DCB B270R User Guide
Samsung Fax Machine SF4000 User Guide
Samsung Tablet GTP3100TSLTTT User Guide
Sanyo Computer Monitor VMC 8114PA User Guide
Screenlife Video Games Seinfeld User Guide