Washing Machine
Owner’s Instructions
B1445AV/
B1245AV/
B1245AS/
B1245A/
B1045A/
R1245AV/
R1045A/
F1245AV/
F1045A
Installing the Washing Machine
Installing the Washing Machine
Selecting a location
Unpacking the Washing Machine
Before you install the washing machine, select a location with the following characteristics:
Unpack your washing machine and inspect it for shipping damage. Also make sure that
you have received all of the items shown below. If the washing machine was damaged
during shipping or you do not have all of the items, contact your Samsung dealer
immediately.
•
•
•
•
•
A hard, level surface (if the surface is uneven, see "Adjusting the leveling feet," below)
Away from direct sunlight.
Adequate ventilation
Room temperature that will not fall below 0 ˚C
Away from sources of heat such as coal or gas
Overview of the washing machine
Make sure that the washing machine does not stand on its power cord.
Ventilation openings must not be obstructed by carpeting when the washing machine is
installed on a carpeted floor.
Adjusting the leveling feet
Worktop
If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under
the feet):
1. Loosen the leg bolt by turning it with your hand until it is at the desired height.
2. Tighten the locking nut by turning it with the supplied wrench.
D
Drain Hose
Control panel
•
Place the washer on a sturdy, flat surface.
If the washer is placed on an uneven or weak surface, noise or vibration occurs.
(Only a l degrees angle is allowed.)
Plug
Removing the shipping bolts
Before using the washing machine, you must remove the five shipping bolts from the back
of the unit. To remove the bolts:
2
1
Base cover
Adjustable feet
3
Debris filter
1. Loosen all bolts with the supplied wrench before removing them.
2. Take each bolt head and pull it through the wide part of the hole.
Repeat for each bolt.
Emergency drain
tube
3. Fill the holes with the supplied plastic covers.
Filter-cover
4. Keep the shipping bolts for future use.
Connecting the water supply hose(Option)
4. Connect the water supply hose to the adaptor.
1. Remove the adaptor from the
Pull down part (c) of the water supply hose.
water supply hose.
c
When you release part (c) the hose automatically
Cold Water
supply hose
connects to the adaptor making a ’click’ sound.
2. First, using a “+” type screw driver, loosen the
four screw s on the ad aptor. N ext, take the
adaptor and turn part(b) following the arrow until
there is a 5mm gap.
5. Connect the other end of the water supply hose
to the inlet water valve at the top of the washer.
Screw the hose clockwise all the way in.
Wrench
Drain hose
3. Connect adaptor to the water tap by tightening
the screws firmly.
Then, turn part (b) following the arrow and put(a)
and (b) together.
•
If the water tap has a screw type faucet, connect
the water supply hose to the tap as shown.
a
b
Bolt hole
covers
Hose guide
NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. Use
the most conventional type of faucet for water supply. In case the faucet is square or too
big, remove the spacing ring before inserting the faucet into the adaptor.
2
SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 3
Installing the Washing Machine
Installing the Washing Machine
Connecting the water supply hose
Plugging in the machine
The water supply hose must be connected to the washing machine at one end and to the
water faucet at the other. Do not stretch the water supply hose. If the hose is too short and
you do not wish to move the water faucet, replace the hose with a longer, high pressure
hose.
For European Users. You will NOT need to ground the plug of the washing machine.
For U.S. Users. You MUST ground the plug of the washing machine.
Check with a licensed electrician before using the machine to make sure it is properly
grounded.
To connect the water supply hose:
1. Take the L-shaped arm fitting for the cold
water supply hose and connect to the cold
water supply intake on the back of the
machine. Tighten by hand.
For U.K. Users.
Wiring lnstructions
WARNING THIS APPLIANCE MUST BE EARTHED.
This appliance must be earthed. In the event of an
GREEN AND
YELLOW
13 AMP
FUSE
electrical short circuit, earthing reduces the risk of electric
shock providing an escape wire for the electric current.
The appliance is equipped with a mains lead which
includes an earth wire for connecting to the earth terminal of
your mains plug.
2. Connect the other end of the cold water supply hose to your sink's cold water faucet and
tighten it by hand. If necessary, you can reposition the water supply hose at the washing
machine end by loosening the fitting, rotating the hose, and retightening the fitting.
Option: 1. Take the red L-shaped arm fitting for the hot water supply hose and connect
to the red hot water supply intake on the back of the machine. Tighten by
hand.
The plug must be plugged into a socket that is properly
installed and earthed.
*The wires in this mains lead are coloured in accordance
with the following code:
• Green and yellow
: Earth
: Neutral
: Live
2. Connect the other end of the hot water supply hose to your sink's hot water
faucet and tighten it by hand.
• Blue
• Brown
3. Use a Y-piece if you only want to use cold water.
• AS the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings indentifying the terminals in your plug,
proceed as follows.
Note: The appliance is to be connected to the water mains using new hose-sets and that
old hose-sets should not be used.
BROWN
BLUE
• Connect the green and yellow wire to the terminal
in the plug marked with the letter E or the earth
Positioning the drain hose
The end of the drain hose may be positioned in three ways:
Over the edge of a sink
The drain hose must be placed at a height of
between 60 and 90 cm. To keep the drain hose
spout bent, use the supplied plastic hose
guide. Secure the guide to the wall with a
hook or to the faucet with a piece of string to
prevent the drain hose from moving.
symbol (
yellow.
) or coloured green or green-and-
WARNING
Ensure that the plug and power
cord are not damaged before use. If
you have any reason to remove the
moulded plug from this appliance,
immediately remove the fuse and
dispose of the plug.
Do not connect the plug to a mains
socket under any circumstances as
there is a danger of electric shock.
• Connect the blue wire to the terminal marked
with the letter N or coloured black.
• Connect the brown wire to the terminal marked
with the letter L or coloured red.
* Consult a qualified electrician or service technician if
in doubt about any of these instructions.
The manufacturer of this washing machine will
not accept any liability for damage to persons or
material for non observance of these requirements.
There are no user serviceable parts inside the
washing machine and if the mains lead of this
appliance is damaged, it must only be replaced by
qualified service personnel approved by the
manufacturer because special tools are required.
CIRCUITS
Your washing machine should be
operated on a separate circuit
from other appliances. Failure to
do this may cause the circuit
breaker to trip or the fuse to blow.
ln a sink drain pipe branch
The drain pipe branch must be above the sink siphon so that the end of the hose is at least
60 cm above the ground.
ln a drain pipe
Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60
cm and no longer than 90 cm.
4
SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 5
Washing a Load of Laundry
Washing a Load of Laundry
Overview of the control panel
7. Silver Nano selection button
1. Digital graphic display
Silver Nano water is supplied in washing as well as the last rinse, featuring sterilization
and antibacterial coating.
Displays the remaining wash cycle time,all of washing information and error messages.
2. Prewash selection button
8. Half Load selection button
Press the button to select pre-wash. Pre-wash is available only with Cotton, Coloureds,
Synthetics, Delicates,baby programs.
Press the button in case of half load(about 1~4kg) washing. This function saves washing
time and energy.
3. Temperature selection button
9. Child Lock selection button
Press the button repeatedly to cycle through the available water temperature options
This is a button for preventing children from manipulating the washing machine.
On/ Off - To set the program on: Press the Start/ Pause button to turn on the washing
machine. Press and hold down the [Rinse] + [Spin] button for 2-3 seconds. It can only be
activated when the machine is turned on. Once you set the baby program on while in
washing, no button is activated until you set if off. Even the POWER button will not be
activated. The Baby Program lamp lights on. To set the program off: Press and hold down
the [Rinse] + [Spin] button again for 2-3 seconds, then the lamp lights off and is set off.
(cold water( ), 30 ˚C, 40 ˚C , 60 ˚C and 95 ˚C).
4. Rinse selection button
Press the rinse button to add rinse cycles. Maximum number of rinse cycles is five.
5. Spin selection button
Press the button repeatedly to cycle through the available spin speed options.
Note: Check out the Baby Program button first when no button is activated while the
B1445AV
, 400, 800, 1200, 1400 rpm
, 400, 800, 1000, 1200 rpm
, 400, 600, 800, 1000 rpm
,
,
,
washing machine is working.
B1245AV/ B1245AS/ B1245A/ R1245AV/ F1245AV
B1045A / R1045A / F1045A
10. Fuzzy Control dial
Turn the dial to select one of the 14 available wash programs.
Cotton, Coloureds, Synthetics, Delicates, Wool, Hand wash, Quick,
Rinse+Spin, Spin, Drain, Baby Program(Stains, Delicates, Coloreds, Cotton)
: no spin, : rinse hold
No spin
The laundry remains in the drum without being spun after the final drain
Rinse Hold
11. Start/Pause selection button
The laundry remains soaking in the final rinse water.
Press to pause and restart programs.
Before the laundry can be unloaded, either “Drain” or the “Spin” program must be run.
12. (On/Off) selection button
6. Delay Start selection button
Press once to turn the washing machine on, press again to turn the washing machine off.
If the washing machine power is left on for longer than 10 minutes without any buttons
being touched, the power automatically turns off.
Press the button repeatedly to cycle through the available delayed start options (from 3
hour to 24 hours in one hour increments).
Displayed hours means the time of finished washing-cycle.
6
SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 7
Washing a Load of Laundry
Washing a Load of Laundry
Washing clothes using Fuzzy Logic
Washing for the first time
Before washing clothes for the first time, you must run a complete cycle without clothes.
To do this:
Your new washing machine makes washing clothes easy, using Samsung's "Fuzzy Logic"
automatic control system. When you select a wash program, the machine will set the correct
temperature, washing time, and washing speed.
To wash clothes using the Fuzzy Logic programs:
1. Press the (On/ Off) button.
2. Pour a little detergent into compartment
in the
1. Turn on your sink's water faucet.
2. Press the (On/ Off) button.
detergent drawer.
3. Open the door.
3. Turn on the water supply to the washing machine.
4. Press the Temperature button repeatedly until
40 ˚C is displayed.
4. Load the articles one at a time loosely into the drum, without overfilling.
5. Close the door.
6. Add the detergent, softener, and pre-wash detergent (if necessary) into the appropriate
5. Press the Start/ Pause button.
compartment.
This will remove any water from the manufacturer’s
•
Note: Pre-wash is only available when washing Duvet, Bedding, Towel, Curtain,
Cotton, Coloureds, Synthetics and Delicates programs.
test run remaining in the machine.
It is only necessary if your clothing is heavily soiled.
Dispender :Detergent for prewash or starch.
7. Turn the Fuzzy Control dial to select the
appropriate program for the type of
clothes Cotton, Coloureds, Synthetics,
Delicates, Wool, Hand wash, Quick,
Rinse+Spin, Spin, Drain, Baby
Program(Stains, Delicates, Coloreds,
Cotton)
Dispenser
Dispenser
: Detergent for main wash, water softener,pre-soaking agent, bleach and stain removal product.
: Additives,e.g.fabric softener or former (fill no higher than lower edge of insert “ A”)
Putting detergent in the washing machine
1. Pull out the detergent drawer.
2. Add laundry detergent into compartment
3. Add softener into compartment (if you desire).
You will see the indicators light up on
the control panel.
.
4. Add prewash detergent into compartment
(if you desire).
Caution :
Concentrated or thick fabric softener and
conditioner must be diluted with a little water
8. At this time, you can control the wash temperature, rinsing times, spin speed, delay time
by pressing the appropriate option button.
before being poured into the dispenser (prevents
the overflow from becoming blocked.)
9. Press the Start/ Pause button on the Fuzzy Control dial and the wash cycle will begin.
The process indicator will light up and the remaining time for the cycle will appear in the
display.
When the cycle is finished:
After the total cycle has finished, the power will turn off automatically.
1. Open the door.
Note: The door will not open untill 3 minutes after the machine stops or the power turns
off.
2. Remove laundry.
8
SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 9
Washing a Load of Laundry
Washing a Load of Laundry
Washing tips and hints
Washing clothes manually
Sorting your laundry : Sort your laundry according to the following characteristics:
You can wash clothes manually without using the Fuzzy Logic feature. To do so:
Type of fabric care label symbol : Sort laundry into cottons, mixed fibers, synthetics,
•
1. Turn the water supply on.
silks, wools and rayon.
2. Press the
(On/ Off) button on the washing machine.
3. Open the door.
4. Load the articles one at a time loosely into the drum, without overfilling.
5. Close the door.
6. Put the detergent and, if necessary, softener or prewash detergent, in the appropriate
compartments.
Colour : Divide whites and colours. Wash new, coloured items separately.
•
Size: Placing items of different sizes in the same load will improve the washing action.
•
Sensitivity: Wash delicate items separately, using the Delicate wash program for pure
new wool, curtains and silk articles. Check the labels on the items you are washing or
refer to the fabric care chart in the appendix.
•
7. Press the Temperature button to select the temperature
(cold water, 30˚C, 40˚C, 60˚C, 95˚C)
Emptying pockets : Coins, safety pins and similar items can damage linen, the
washing machine drum, and the water tank.
8. Press to rinse button to select the required number of rinse cycles.
Maximum number of rinse cycles is five.
Securing fasteners : Close zippers and fasten buttons or hooks; loose belts or ribbons
The washing duration will be prolonged accordingly.
9. Press the Spin button to select the spin speed.
should be tied together.
Prewashing cotton : Your new washing machine, combined with modern detergents,
will give perfect washing results, thus saving energy, time, water and detergent. However,
if your cotton is particularly dirty, use a prewash with a protein-based detergent.
Note: The rinse hold program allows you to take clothes that are dripping wet
out of the washing machine.
: No Spin,
: Rinse Hold.
Determining load capacity: Do not overload the washing machine or your laundry
may not wash properly. Use the chart below to determine the load capacity for the type of
laundry you are washing.
10. Press the button repeatedly to cycle through the available delayed start options
(from 3 hour to 24 hours in one hour increments). Displayed hours means the time
of finished washing-cycle.
Fabric Type
Load Capacity
11. Press the Start/ Pause button and the machine will begin the cycle.
B1445AV/ B1245AV/ B1245AS/ R1245AV/ R1045A F1245/ F1045
B1245A/ B1045A/
Coloured/ cotton
-average/ lightly soiled
-heavily soiled
Synthetics
Delicates
Wools
Using Delay Start
6.0 kg
6.0 kg
3.0 kg
2.5 kg
2.0 kg
5.2 kg
5.2 kg
3.0 kg
2.0 kg
1.5 kg
4.5 kg
4.5 kg
3.0 kg
2.0 kg
1.5 kg
You can set the washing machine to finish your wash automatically at a later time, choosing
from 3 to 24 hour delay (in 1 hour increments). Displayed hours means the time of finished
washing-cycle.
To do this:
1. Manually or automatically set your washing machine for the type of clothes you are
washing.
Detergent tips: The type of detergent you should use is based on the type of fabric
(cotton, synthetic, delicate items, wool), colour, wash temperature, degree and type of
soiling. Always use "low suds" laundry soap, which is designed for automatic washing
machines.
2. Press the Delay Start button repeatedly until the delay time is set.
3. Press the Start/ Pause button. The Delay Start indicator will light, and the clock will
begin counting down until it reaches your finish time.
4. To cancel Delay Start, press the (On/ Off) button, then turn the washing machine
on again.
Follow the detergent manufacturer's recommendations based upon the weight of the
laundry, the degree of soiling, and the hardness of the water in your area. If you do not
know how hard your water is, ask your water authority.
Note: Keep detergents and additives in a safe, dry place out of the reach of children.
10 SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 11
Maintaining the Washing Machine
Maintaining the Washing Machine
Cleaning the detergent drawer and recess
Draining the washing machine in an emergency
B1445AV/ B1245AV/ B1245AS/ B1245A/ B1045A
1. Press the release lever on the inside
of the detergent drawer and pull it out.
1. Unplug the washing machine
from the power supply.
2. Open the filter-cover by using
a coin or a key.
2. Remove the cap from compartment
.
3. Wash all of the parts under running water.
4. Clean the drawer recess with an old toothbrush.
5. Reinsert the cap (Pushing it firmly into place)
and replace the liquid detergent divider into the drawer.
6. Push the drawer back into place.
7. Run a rinse program without any laundry in the drum.
3. Unscrew the emergency drain cap
by turning left. Grip the cap on the
end of the emergency drain tube
and slowly pull it out about 15 cm.
Cleaning the debris filter
Clean the debris filter 5 or 6 times a year, or when you see the following error message on
the display:
4. Allow all the water to flow into a bowl.
5. Reinsert the drain tube and screw the cap back on.
6. Replace the filter-cover.
1. Open the filter-cover,
See “Draining the washing machine in an emergency" on page 12.
2. Unscrew emergency drain cap by turning left and drain off all the water.
Repairing a frozen washing machine
See "Draining the washing machine in an emergency" on page 12.
If the temperature drops below freezing and your washing machine is frozen:
1. Unplug the washing machine.
3. Unscrew the filter cap and take it out.
2. Pour warm water on the source faucet to loosen the water supply hose.
3. Remove the water supply hose and soak it in warm water.
4. Pour warm water into the washing machine drum and let it sit for 10 minutes.
5. Reconnect the water supply hose to the water faucet and check if the water supply
and drain operations are normal.
Cleaning the exterior
1. Wipe the washing machine surfaces, including the control panel, with a soft cloth
and non-abrasive household detergents.
2. Use a soft cloth to dry the surfaces.
3. Do not pour water on the washing machine.
4. Wash any dirt or other material from the filter. Make sure the drain pump propeller
behind the filter is not blocked. Replace the filter cap.
5. Replace the filter-cover.
12 SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 13
Maintaining the Washing Machine
Troubleshooting
Cleaning the water hose mesh filter
You should clean the water hose mesh filter at least one time per year, or when you see the
following error message on the display:
Problems and solutions
The washing machine will not start
•
•
•
•
Make sure the door is firmly closed.
Make sure the washing machine is plugged in.
Make sure the water source faucet is turned on.
Make sure to press the Start/ Pause button.
No water or insufficient water supply
•
•
•
•
Make sure the water source faucet is turned on.
Make sure the water source hose is not frozen.
Make sure the water intake hose is not bent.
To do this:
1. Turn off the water source to the washing machine.
2. Unscrew the hose from the back of the washing machine.
Make sure the filter on the water intake hose is not clogged.
Detergent remains in the detergent drawer after the wash
program is complete
3. With a pair of pliers, gently pull out the mesh filter from the end of the hose and rinse
it under water until clean. Also clean the inside and outside of the threaded
connector.
•
•
Make sure the washing machine is running with sufficient water pressure.
Put the detergents in the inner parts of the detergent drawer(away from the
outside edges).
Washing machine vibrates or is too noisy
•
Make sure the washing machine is set on a level surface. If the surface is not level,
adjust the washing machine feet to level the appliance (see page 3).
Make sure that the shipping bolts are removed (see page 3).
Make sure the washing machine is not touching any other object.
Make sure the laundry load is balanced.
•
•
•
The washing machine does not drain and/or spin
•
•
Make sure the drain hose is not squashed or bent.
Make sure the debris filter is not clogged
(see page 14).
The Door does not open
The door will not open until 3 minutes after the machine stops or the power turns off.
•
Understanding error messages
4. Push the filter back into place.
Error displayed
Solution
5. Screw the hose back onto the washing machine.
6. Turn on the faucet and make sure the connections are watertight.
• Close the door.
• Make sure the source water faucet is turned on.
• Check the water pressure.
• Clean the debris filter.
• Make sure the drainage hose is installed correctly.
• Laundry load is unbalanced; loosen any tangled laundry.
If only one item of clothing needs washing, such as a bathrobe or
jeans, the final spin result might be unsatisfactory and an "UE"
error message will be shown in the display window.
• Call after-sales service.
Before contacting After-Sales service:
1. Try to remedy the problem (See "Troubleshooting" on this page).
2. Restart the programme to see if the fault is repeated.
3. If the malfunction persists, call after-sales service and describe the problem.
14 SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 15
Programme Chart
Programme Chart
(●●●user option)
(
●●●user option)
DETERGENT
AND ADDITIVES
Tem
(˚C)
DETERGENT
AND ADDITIVES
Tem
(˚C)
Max load
(kg)
Max load
(kg)
Spin Speed(MAX)rpm
B1245AV
Spin Speed(MAX)rpm
B1245AV
Delay
start
Delay
start
Half
Half
PRO-
GRAM
PRO-
GRAM
B1445AV
B1245AV
B1245AS
B1245A
B1445AV
B1245AV
B1245AS
B1245A
B1045A
R1045A
F1045A
Load
Load
B1045A
B1245AS
R1245AV F1245AV
B1245AS
B1245A
F1245AV
F1045A
R1245AV
R1045A
Sof-
Sof-
Pre-
Pre-
Max B1445AV
Max B1445AV
B1245A
wash
wash
R1045A
F1045A
tener
tener
R1045A F1045A wash
wash
R1245AV
F1245AV
R1245AV
F1245AV
B1045A
B1045A
Cotton
6.0
6.0
5.2
5.2
4.5
4.5
●
●
yes
yes
●
95
60
1400
1400
1200
1200
1000
1000
●
●
●
●
Baby Cotton
6.0
6.0
5.2
5.2
4.5
4.5
●
yes
yes
●
95
60
1400
1400
1200
1200
1000
1000
●
●
●
●
Baby
Coloureds
●
●
●
Coloureds
Baby
Synthetics
Delicates
Wool
3.0
2.5
2.0
2.0
2.0
3.0
2.5
1.5
1.5
1.5
3.0
2.0
1.5
1.5
1.5
●
●
-
yes
yes
yes
yes
yes
●
●
●
●
●
60
40
40
40
60
800
800
400
400
1400
800
800
400
400
1200
800
600
400
400
1000
●
●
●
●
●
●
●
●
●
●
2.5
6.0
2.0
5.2
2.0
4.5
●
●
yes
yes
●
●
60
40
800
800
600
●
●
●
●
Delicates
Baby Stains
1400
1200
1000
PROGRAM
Type of WASH
Handwash
Quick
-
Baby Cotton
Averagely or lightly soiled baby cottons, bed linen, table linen, underwear,
towels, shirts, etc.
-
Baby Coloureds Averagely or lightly soiled baby cottons, bed linen, table linen, underwear,
towels, shirts, etc.
PROGRAM
Type of WASH
Baby Delicates Delicate baby dresses, skirts, shirts and blouses.
Cotton
Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels,
shirts, etc.
Baby Stains
Stains on cottons, bed lined, underwear, towels, etc. caused by food spills and
urine.
Coloureds
Synthetics
Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels,
shirts, etc.
Averagely or lightly soiled blouses, shirts, etc., Made of polyester
(diolen, trevira), polyamide (perlon, nylon) or other similar blends.
Delicates
Wool
Delicate curtains, dresses, skirts, shirts and blouses.
Only machine washable woolens with pure new wool label.
Very light wash course like hand wash.
Handwash
Quick
Lightly soiled cottons or linen blouses, shirts, dark coloured terry cloth,
coloured linen articles, jeans, etc.
1. Programme with prewash lasts approx. 15 minutes longer.
2. The programme duration data has been measured under the conditions specified in
Standard IEC 456.
3. Consumption in individual homes may differ from the values given in the table
due to variations in the pressure and temperature of the water supply, the load and
the type of laundry.
16 SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 17
Appendix
Appendix
Fabric care chart
Protecting the environment
•
This appliance is manufactured from recyclable materials. If you decide to dispose of
this appliance, please observe local waste disposal regulations. Cut off the power
cord so that the appliance cannot be connected to a power source. Remove the door
so that animals and small children cannot get trapped inside the appliance.
Resistant material
Can be ironed at 100 ˚C max
Do not iron
Delicate fabric
•
•
•
Do not exceed the detergent quantities recommended in the detergent manu-
facturers' instructions.
Item may be washed at 95 ˚C
Item may be washed at 60 ˚C
Can be dry cleaned using any solvent
Dry clean with perchloride, lighter fuel,
pure alcohol or R113 only
Use stain removal products and bleaches before the wash cycle only when strictly
necessary.
Item may be washed at 40 ˚C
Dry clean with aviation fuel,
pure alcohol or R113 only
Save water and electricity by only washing full loads (the exact amount depends
upon the program used).
Item may be washed at 30 ˚C
Do not dry clean
Dry flat
Item may be hand washed
Dry clean only
Declaration of conformity
This appliance complies with European safety standards, EC directive 93/ 68 and EN
Standard 60335.
Can be hung to dry
Can be bleached in cold water
Do not bleach
Dry on clothes hanger
Tumble dry, normal heat
Specification
TYPE
FRONT LOADING WASHER
Can be ironed at 200 ˚C max
Tumble dry, reduced heat
Do not tumble dry
B1445AV,B1245AV,B1245AS,B1245A,B1045A R1245AV,R1045A
F1245AV,F1045A
DIMENSION
W598mm × D550mm ×H844mm
W598mm×D450mm×H844mm W598mm×D404mm×H844mm
Can be ironed at 150 ˚C max
WATER PRESSUERE
WATER VOLUME
NET WEIGHT
50 kPa ~ 800 kPa
54L
49L
48L
Electrical warnings
To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in
mind:
75kg
66kg
62kg
WASHandSPINCAPACITY
6kg (DRY LAUNDRY)
5.2kg (DRY LAUNDRY) 4.5kg (DRY LAUNDRY)
B1445AV,B1245AV,B1245AS,B1245A,B1045A
MODEL
R1245AV,R1045A
F1245AV,F1045A
•
Operate the appliance only from the type of power source indicated on the marking
label. If you are not sure of the type of power supplied to your home, consult your
appliance dealer or local power company.
2000W
2400W
220V
240V
220V 1900W 220V 1800W
240V 2200W 240V 2100W
POWER
CONSUMPTION
WASHINGAND
HEATING
B1245AV,B1245AS,
•
Use only a grounded or polarized outlet. For your safety, this appliance is equipped
with a polarized alternating current line plug having one blade wider than the other.
This plug will fit into the power outlet only one way. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, contact
your electrician to replace your outlet.
MODEL
SPIN
B1445AV
550W
B1045A R1245A R1045A F1245A F1045A
500W 550W 500W 250W 220W
34W
B1245A
230V
500W
PUMPING
MODEL
PAPER
PLASTIC
MODEL
rpm
B1445AV,B1245AV,B1245AS,B1245A,B1045A
R1245AV,R1045A F1245AV,F1045A
•
•
Protect the power cord. Power supply cords should be routed so that they are
unlikely to be walked on or pinched by items placed on or against them. Pay
particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the unit.
2.5kg
1.0kg
2.1kg
0.9kg
1.9kg
0.8kg
PACKAGE Wt
B1445AV,B1245AV,B1245AS,B1245A,B1045A
B1445AV
1400
B1045A,R1045A,F1045A
1000
SPIN REVOLUTION
Do not overload the wall outlet or extension cords. Overloading can result in fire or
electric shock.
1200
18 SAMSUNG Washing Machine Owner’s Instructions
SAMSUNG Washing Machine Owner’s Instructions 19
IN CASE THE NEED FOR
SERVICING ARISES
-Don't hesitate to call any AS center nearby
with your name, address, telephone number,
model number and serial number of your machine
when anything wrong with your product occurs.
Code No.: DC68-01986J
|