SCC-B9372
DAY&NIGHT IR LED CAMERA
operating instructions
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
CAUTION
1. Do not drop objects on the product or apply strong shock to it.
Keep away from a location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 122°F), low temperature
(below 14°F), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power
and then move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning.
Neglecting to do so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun,
as this may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at
any time.
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus.
13. Unplug this apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or been dropped.
contents
02
02
Features
FEATURES
02
Things to keep in mind during installation and
use
THINGS TO KEEP IN MIND
DURING INSTALLATION
AND USE
02
03
04
Function
Installation method
FUNCTION &
INSTALLATION
03
05
06
Troubleshooting
Specifications
TROUBLESHOOTING
05
SPECIFICATIONS
06
DIMENSIONS
07
07
Dimensions
contents _01
features
•
•
•
•
•
•
•
•
SONY 1/3” Super HAD High-resolution Colour CCD
Resolution: 540TVL (Colour), 570TVL (B/W)
Externally Adjustable Focal Length & Focus by Rings
Filter Changeable Vari-Focal DC Auto Iris 3.8~9.5mm F1.2 Lens Built -in.
Colour & B/W Auto Switchable by Photocell and Sensitivity
CDS Auto Switching IR LED Control (42 IR LEDs)
Externally Adjustable DC Iris Level
Dip Switch control of Day & Night time delay, Flickerless
BLC and White Balance
•
•
AC24V/DC12V Dual Power Available
Waterproof Outdoor Installation (IP-66)
things to keep in mind during
installation and use
•
•
Do not disassemble the camera on your own.
Always be careful when handling the camera. Do not strike the camera by your
fists or shake it. Please be careful not to be careless when storing and operat-
ing it.
•
•
•
Do not place or operate the camera in any wet environment such as rain or
wet surfaces.
Do not clean the camera with rough sandpaper. Please always use a dry cloth
when cleaning it.
Put the camera in a cool area free from direct sunlight. Otherwise, the camera
may be damaged.
02_ features
function & installation
VIDEO
6
2
1
POWER
4
5
3
[THE OTHER SIDE VIEW]
FUNCTION
1
2
Protective Film over Front Glass : Remove this film before operating the Camera.
Focus/Zoom Lever Bolt Screws: Used to fix the Focus/Zoom ring to the lens internally.
Be careful not to lose this small bolt screws which need not be touched other than by a
service technician.
3
Focus/Zoom Ring Fixing Screws: Used to fix the Focus/Zoom Ring at the desired
position after adjusting the lens angle and focus setting as described below.
4
Focus and Zoom Ring: These two rings are used to accurately adjust the viewing angle
and to sharply focus all objects within the lens field of view.
3
- Loosen the fixing screws (
) to turn the Zoom and Focus ring.
i) To widen the viewing angle turn the “Zoom Ring” to “W” (Wide).
ii) To obtain a closer view turn this ring to “T” (Tele).
- After adjustment of the viewing angle then adjust the “Focus Ring” between “N” (Near) or “
(Far) until the sharpest focus is achieved.
”
3
- Then tighten the fixing screws (
) on each ring.
- After tightening you should check that angle and focus is still accurate.
5
DC Level Volume Screw Cap :
- Loosen the DC level volume screw cap on the camera body.
i) For a brighter screen turn the DC level volume slowly toward “H” (counter-clockwise),
ii) For a darker screen turn it toward “L” (clockwise) with a driver.
6
Bracket : Used to install the camera to the desired location.
function & installation _03
INSTALLATION METHOD
Bracket & Camera Mounting
- Install the Mounting Bracket at the desired location.
Connecting to Monitor and Power
- Set the impedance switch to the 75 standard position unless a video equipment is connected
to the monitor video out.
- Adaptor: AC24V / 800mA or DC12V / 1A (AC24V / DC12V Model)
• Be sure to connect power after all the installation is done.
• Do not use power sources other than that specified.
- After adjusting view angle, cap over the camera with the sun-shield and fix it to the camera with
the sun-shield bolt.
04_ function & installation
troubleshooting
If you have trouble operating the camera, check the following guides for the
possible problem.
•
Nothing appears on the screen.
- Check the power connection and video signal line connection.
- Check the brightness level of DC Auto Iris volume of the camera.
•
The video image is not clear.
- Check if the camera glass has dust on the surface.
Clean the camera glass with a clean cloth or brush.
- Make sure that the screen is not exposed directly to a bright light.
Adjust the position of the camera if necessary.
- Check if protective film of camera glass is removed.
•
•
The screen is dark
- Adjust the brightness feature of the monitor.
- Check the brightness level of DC Auto Iris volume of the camera.
The screen does not properly display when IR LEDs work.
- Check if the camera glass has dust.
- Clean the camera glass with a clean cloth or brush.
If you cannot solve the problem with above guidelines, please contact an
authorized technician.
troubleshooting _05
specifications
ITEM
PAL
Image Sensor
Effective Pixels
Scanning System
Scanning Frequency
Resolution
1/3" Interline transfer type colour CCD (SONY)
752H × 582V (440K pixels)
625 Lines 2:1 Interlace
15.625KHz (H), 50Hz (V)
540TVL (Colour), 570TVL (B/W)
1/50 sec.
Shutter Speed
S/N Ratio
More than 48dB (AGC Off)
Internal
Sync. System
Min. Illumination
White Balance
Video Output
Lens
0 Lux (IR LED On)
ATW / AWC selectable
VBS 1.0 Vp-p (75 Load)
3.8~9.5mm Vari -Focal, DC Auto Iris F1.2 Day & Night Lens
AC24V 10%, DC12V 10%
Power Supply(*)
Power Consumption
2.5W(LED Off)/7.8W(LED On)
Operating Temp.
Operational Humidity
Dimensions
-10˚C~50˚C (14˚F~122˚F)
Max. 90% RH
77.5mm (Ø) × 129mm (L)
(*) Must use regulated & specified power supply.
06_ specifications
dimensions
[IR-LED 42pcs]
[BODY & SUN-SHIELD]
[BRACKET]
dimensions _07
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems)
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
|