2 x10″ Plus 5” Stackable
Aluminum Drive Bass Enclosure
Hartke
Connecting the 2.5XL
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance
are wired in "Parallel", the total imped-
ance is cut in half and when two speak-
ers are wire in “Series”, the total imped-
ance is the sum of the speakers individ-
ual impedance.
EFFECT
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
The 2.5XL impedance is 8 Ohms. So,
when two 2.5XL’s are connected
together in parallel, the total impedance
is 4 Ohms. The impedance of your
speaker also has an effect on your
amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
Hartke
2.5XL BASS CABINET
200 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
8
IMPORTANT: There is a minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
Connecting the 2.5XL to Your Amplifier
The 2.5XL connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the 2.5XL’s rear
jackplate.
EFFECT
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
Hartke
2.5XL BASS CABINET
200 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
8
Using the EXTENSION Output
The 2.5XL provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook up
with your amplifier. Follow the steps
below to connect two 2.5XL’s using the
Extension Output. Connect the
Amplifier Output to the Input of the first
2.5XL. Now, connect the Extension
Output to the Input of the second
2.5XL.
Hartke
2.5XL BASS CABINET
200 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
Specifications
Hartke 2.5XL Specifications
Type
Tuned, Vented Enclosure
8 Ohms Impedance
Impedance (Ohms)
Power Handling
Drivers
200 Watts RMSPower Handling
1 - Hartke 5XL8 and 2 - 10XL16
Special Design Aluminum 10",
16 ohm,100 watt drive units
99dB @ 1W/1M
SPL
Frequency Response
Inputs
35Hz - 12kHz
Parallel 1/4”
Weight
66 lbs. (29.94 kg)
Dimensions
Height:18" (45.72 cm)
Width: 24" (60.96 cm)
Depth: 18" (45.72 cm)
Hartke
Distributed Worldwide Exclusively by:
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
|