Mid-Size Vandal Dome Camera
Manual
(3.6mm model shown)
Model No.
Resolution
Lens Size
# of IR LEDs
NTSC
EV-2166-N3WQ
EV-2166-NVWQ
EV-2766-N3WQ
EV-2766-NVWQ
420 TV lines
420 TV lines
540 TV lines
540 TV lines
3.6mm
4~9mm
3.6mm
4~9mm
18
21
18
21
PAL
EV-2166-P3WQ
EV-2166-PVWQ
EV-2766-P3WQ
EV-2766-NVWQ
420 TV lines
420 TV lines
540 TV lines
540 TV lines
3.6mm
4~9mm
3.6mm
4~9mm
18
21
18
21
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
SECO-LARM Mid-Size Vandal Dome Cameras
Overview:
Models ending in
NVWQ or PVWQ only.
Focus
Zoom
Camera
Set screw
Dome cover
Female BNC connector
DC plug with
Wiring notch
terminal block
DC jack
Important:
Do not cut the DC jack or
the female BNC connector
as this will void the
warranty.
Mounting base
Mounting screw
Before Starting:
1. Please read this manual carefully and keep it for future
reference.
5. Do not drop the camera or subject it to strong
vibrations.
2. Use the camera within given temperature and electricity
limits.
3. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
4. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals*
Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-gaussing, which occurs automatically with many
monitors when turned on.
Installation:
1. Run hidden cables from the video source and 12VDC
power supply to the camera. Do not cut the DC jack or
the female BNC connector as this will void the
warranty. If needed, use the included SECO-LARM
DC plug with terminal block.
6. Mount the mounting base to the wall using the 3
included mounting screws. If necessary, use the
included screw anchors.
7. Adjust the camera angle as shown on page 2,
Adjusting the Camera Angle.
8. Test the video signal.
2. Test to make sure the voltage is correct.
Use only 12VDC.
9. Models ending in NVWQ and PVWQ only: Adjust
the zoom and focus by hand or with a small
screwdriver to loosen the knob, and then sliding the
knob left or right. IMPORTANT: Do not use power
tools. Lens damage may result.
3. Undo the 3 set screws on the side of the dome cover
using the included allen wrench and remove the dome
from the base.
4. Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location with a pencil.
5. If the installation involves surface wiring, use the wiring
notch located on the side of the mounting base
to run wires.
10. Reattach the dome to the camera.
11. Use the included allen wrench to tighten the set
screws, securing the dome to the base.
12. Do a final test of the video camera and monitor.
SECO-LARM U.S.A., Inc.
3
SECO-LARM Mid-Size Vandal Dome Cameras
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
E-mail: [email protected]
PICSN4
MiEV-2x66-xxWQZZ_1011.docx
4
SECO-LARM U.S.A., Inc.
|