Vandal Rollerball Cameras
Manual
NTSC Models
EV-2706-N3GQ
EV-122C-DVB3Q EV-125C-DVB3Q
EV-2706-N3WQ EV-2706-P3WQ
PAL Models
EV-2706-P3GQ
Resolution Housing DNR WDR
600 TVL
480 TVL
600 TVL
480 TVL
Gray
Gray
White
White
EV-122C-DVH3Q EV-125C-DVH3Q
3X – Clear images in nearly any lighting situation
EV-2726-N3GQ*
EV-2726-N3WQ*
EV-2726-P3GQ*
EV-2726-P3WQ*
700 TVL
700 TVL
Gray
White
*Includes built-in OSD (On-Screen Display) controller
1/3” Sony CCD
Weatherproof (IP66)
Split-glass design to
eliminate IR reflection
3.6mm Lens
3-Axis ball mount for wall or
Vandal-resistant design
ceiling mounting
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
ENFORCER Vandal Ball-Mount Dome Cameras
Overview:
Screws
Case
(Only 2 shown. Use all 4 when installing.)
Camera ball
Base
Female BNC
connector
DC Plug with
terminal block
OSD Controller
DC Jack
(3X Models only)
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
4. Do not drop the camera or subject it to
strong vibrations.
2. Use the camera within the given temperature and
electricity limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
Installation:
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted.
5. Put the case over the cameral ball onto the base. Be
careful to not drop the camera ball.
6. Holding the case loosely on the base, turn the camera
2. Loosen the set screws with the included hex wrench
and remove the case from the base.
ball to the desired direction.
NOTE: Before securing installation, make sure to check
both the day and night images. Adjust the camera ball
in a way so that there are no objects blocking or
obscuring the camera’s view.
NOTE: The camera ball is NOT attached to the case
or the base. It sits loose inside the case. Therefore,
be very careful when removing the case from the
base. Do not drop the camera ball.
7. 3X Models Only: Use the OSD controller joystick to
adjust camera settings (see the separate OSD manual).
8. Once the ball is pointing in the desired direction,
tighten the outer case ring to secure the camera in
its position.
3. Mount the base to the wall using the four included
mounting screws. If the wall is made of dry wall, brick,
or similar material, it may be necessary to use the
included plastic screw anchors.
4. Run the camera’s BNC and power connectors through
the camera base, and connect to the video and power
wires that were run through the wall.
9. Do a final test of the video camera and monitor.
SECO-LARM U.S.A., Inc.
3
ENFORCER Vandal Ball-Mount Dome Cameras
Troubleshooting:
Check that the camera is powered up
Check that the power supply’s polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the
monitor is connected properly
The screen is black
Check that there are no objects very close to the camera
Check that there are no highly reflective objects in the scene
The image is foggy or washed out at night
The screen image is dim
Clean the lens using a soft, clean cloth
Check that the light source is adequate
Adjust the monitor’s contrast knob
Change the position of the camera
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot
IR LEDs do not turn on
Change the position of the camera
Change the position of the camera
Check that the correct power supply is in use
Check that the correct power supply is in use
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
E-mail: [email protected]
PICSN4
MiBallMountCamera_1208.docx
4
SECO-LARM U.S.A., Inc.
|