OPERATOR'S MANUAL
Drywall Screwdriver
Model No. DSG50
DOUBLE INSULATED
THANK YOU FOR BUYING A RYOBI DRYWALL SCREWDRIVER.
Your new screwdriver has been engineered and manufactured to Ryobi's high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator's manual before using your new screwdriver.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your screwdriver properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
GENERAL SAFETY RULES
■
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, cloth-
ing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in mov-
ing parts.
WARNING:
Read and understand all instructions. Failure to fol-
low all instructions listed below, may result in elec-
tric shock, fire and/or serious personal injury.
■
■
■
■
Avoid accidental starting. Be sure switch is off
before plugging in. Carrying tools with your finger
on the switch or plugging in tools that have the switch
on, invites accidents.
SAVE THESE INSTRUCTIONS
Work Area
Remove adjusting keys or wrenches before turn-
ing the tool on. A wrench or a key that is left at-
tached to a rotating part of the tool may result in
personal injury.
■
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
■
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases, or dust. Power tools may create
sparks which may ignite the dust or fumes.
Do not overreach. Keep proper footing and bal-
ance at all times. Proper footing and balance en-
ables better control of the tool in unexpected situa-
tions. Do not use on a ladder or unstable support.
■
Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Use safety equipment. Always wear eye protec-
tion. Dust mask, nonskid safety shoes, hard hat, or
hearing protection must be used for appropriate con-
ditions.
Electrical Safety
■
Double insulated tools are equipped with a po-
larized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double insu-
Tool Use and Care
■
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Hold-
ing the work by hand or against your body is un-
stable and may lead to loss of control.
■
■
■
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which it is designed.
lation
eliminates the need for the three-wire
grounded power cord and grounded power supply
system.
Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the switch
is dangerous and must be repaired.
■
Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges, and refrigera-
tors. There is an increased risk of electric shock if
your body is grounded.
Disconnect the plug from power source before
making any adjustments, changing accessories,
or storing the tool. Such preventive safety mea-
sures reduce the risk of starting the tool acciden-
tally.
■
■
Don’t expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord to
carry the tools or pull the plug from an outlet.
Keep cord away from heat, oil, sharp edges, or
moving parts. Replace damaged cords immedi-
ately. Damaged cords increase the risk of electric
shock.
■
■
Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp
cutting edges are less likely to bind and are easier
to control.
■
When operating a power tool outside, use an
outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce
the risk of electric shock.
■
■
Check for misalignment or binding of moving
parts, breakage of parts, and any other condi-
tion that may affect the tool’s operation. If dam-
aged, have the tool serviced before using. Many
accidents are caused by poorly maintained tools.
Personal Safety
■
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inat-
tention while operating power tools may result in
serious personal injury.
Use only accessories that are recommended by
the manufacturer for your model. Accessories that
may be suitable for one tool, may become hazard-
ous when used on another tool.
3
GENERAL SAFETY RULES
■
When servicing a tool, use only identical replace-
Service
ment parts. Follow instructions in the Mainte-
nance section of this manual. Use of unauthorized
parts or failure to follow Maintenance Instructions
may create a risk of electric shock or injury.
■
Tool service must be performed only by quali-
fied repair personnel. Service or maintenance per-
formed by unqualified personnel could result in a risk
of injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
■
Make sure your extension cord is in good condi-
tion. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. A wire gage size (A.W.G.) of at
least 16 is recommended for an extension cord
100 feet or less in length. A cord exceeding 100
feet is not recommended. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
Additional Rules For Safe Operation
■
■
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations,
as well as the specific potential hazards related
to this tool. Following this rule will reduce the risk
of electric shock, fire, or serious injury.
Always wear safety glasses. Everyday eye-
glasses have only impact-resistant lenses; they
are NOT safety glasses. Following this rule will re-
duce the risk of serious personal injury.
■
■
Protect your lungs. Wear a face or dust mask if
the operation is dusty. Following this rule will re-
duce the risk of serious personal injury.
■
■
Inspect for and remove all nails from lumber
before driving screws. Following this rule will
reduce the risk of serious personal injury.
Protect your hearing. Wear hearing protection
during extended periods of operation. Following
this rule will reduce the risk of serious personal in-
jury.
Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or
any medication. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
■
■
Inspect tool cords periodically and, if damaged,
have repaired at your nearest Factory Service
Center or otherAuthorized Service Organization.
Constantly stay aware of cord location. Follow-
ing this rule will reduce the risk of electric shock or
fire.
■
Save these instructions. Refer to them frequently
and use them to instruct others who may use
this tool. If you loan someone this tool, loan them
these instructions also.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended func-
tion. Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
■
Do not abuse cord. Never carry the tool by the
cord or yank it to disconnect it from the recep-
tacle. Keep cord away from heat, oil, and sharp
edges. Following this rule will reduce the risk of elec-
tric shock or fire.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
4
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Hz
W
Amperes
Hertz
Current
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type or a characteristic of current
n
No Load Speed
Rotational speed, at no load
0
Class II Construction
Designates Double Insulated
Construction tools
.../min
Revolutions or Reciprocation Per Minute
Safety Alert Symbol
Revolutions, strokes, surface speed,
orbits etc. per minute
Indicates danger, warning or caution.
It means attention!!! Your safety is
involved.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER:Failuretoobeyasafetywarningwillresultinseriousinjurytoyourselfortoothers. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and
personal injury.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
5
SYMBOLS
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this
product. Read the operator's manual for complete safety, assembly, operating and maintenance, and repair
information.
SYMBOL
MEANING
Do not expose to rain or use in damp locations.
SAVE THESE INSTRUCTIONS
6
FEATURES
VARIABLE SPEED
WARNING:
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is con-
trolled by the amount of switch trigger depression.
Carefully read through this entire operator's manual
before using your new screwdriver. Pay close attention
to the Safety Rules, Warnings and Cautions. If you use
your screwdriver properly and only for what it is
intended, you will enjoy years of safe, reliable service.
BELT CLIP
A convenient feature provided on your screwdriver is a
belt clip. It is molded on top of the motor housing of
your screwdriver.
KNOW YOUR DRYWALL SCREWDRIVER
See Figure 1.
MAGNETIC BIT HOLDER
Beforeattemptingtooperateyourscrewdriver,familiarize
yourself with all operating features and safety
requirements.
Your screwdriver has a magnetic bit holder. The magnet
holds screwdriver bit and screws until ready to drive into
drywall.
ADJUSTABLE NOSEPIECE
WARNING:
Your screwdriver has an adjustable nosepiece for vary-
ing screw depth. It can also be removed for easy bit
changes.
If any parts are missing, do not operate your
screwdriver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
ELECTRICAL CONNECTION
Your screwdriver has a precision built electric motor. It
should be connected to a power supply that is 120
volts, 60 Hz, AC only (normal household current). Do
not operate this tool on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor will
overheat. If your screwdriver does not operate when
plugged into an outlet, double-check the power supply.
SWITCH
To turn your screwdriver ON, depress the switch trigger.
Release switch trigger to turn your screwdriver OFF.
FORWARD/REVERSE LEVER
Your screwdriver has a forward/reverse lever located
above switch trigger for changing direction of bit rotation.
BELT CLIP
ADJUSTING SLEEVE
ADJUSTABLE
NOSEPIECE
1/4 in. (6.4 mm)
SCREWDRIVER
BIT
LOCK-ON
BUTTON
MAGNETIC
BIT HOLDER
FORWARD / REVERSE
LEVER
SWITCH
TRIGGER
Fig. 1
7
PRODUCT SPECIFICATIONS
DRYWALL SCREWDRIVER
DSG50
APPLICATIONS
(Use only for the purpose listed below)
■ Driving screws in drywall.
■ Driving screws in wood.
Bit Shank Size
1/4 in. (6.4 mm) hex
Rating
120 V, 60 Hz, AC only
5.4 Amperes
Input
Switch
Variable Speed
0-4,000 RPM
SCREW CAPACITIES:
No Load Speed
Overall Length
Net Weight
This screwdriver has been designed for driving all com-
mercially available drywall screws.
10.5 in. (267 mm)
3.5 lbs. (1.6 kg.)
OPERATION
FORWARD/REVERSE
LEVER
WARNING:
LOCK-ON
BUTTON
Do not allow familiarity with your screwdriver to make
you careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
SWITCH
See Figure 2.
To turn your screwdriver ON, depress the switch trigger.
Release switch trigger to turn your screwdriver OFF.
LOCK-ON BUTTON
See Figure 2.
SWITCH
TRIGGER
TO INCREASE SPEED,
DEPRESS SWITCH TRIGGER
Your screwdriver is equipped with a lock-on feature
which is convenient when continuous driving of screws
for extended periods of time is required. To lock-on,
depress the switch trigger, push in and hold the lock-on
button located on the side of the handle, then release
switch trigger. Release lock-on button and your
screwdriver will continue running.
Fig. 2
MOLDED
CORD CLIP
To release the lock, depress the switch trigger and
release.
If you have the lock-on feature engaged during use and
your screwdriver becomes disconnected from power
supply, disengage the lock-on feature immediately.
10 FT.
(3 m)
CORD
VARIABLE SPEED
See Figure 2.
Your screwdriver has a variable speed switch designed
to allow operator control of speed and torque limits. The
speed and torque of your screwdriver can be increased
by depressing the switch trigger.
Fig. 3
POWER CORD
See Figure 3.
Note: Depress switch trigger all the way for maximum
speed and torque of your screwdriver. Depress switch
trigger only part of the way for less speed and torque.
Your new screwdriver has a 10 ft. (3 m) power cord that
stays soft and flexible in cold weather. The plug design
is shaped so that it won’t snag on your work during use.
A molded cord clip on the plug makes cord storage
easier.
Avoid running your screwdriver at low speeds for
extended periods of time. Running at low speeds under
constant usage may cause your screwdriver to become
overheated. If this occurs, cool your screwdriver by
running it without a load and at full speed.
8
OPERATION
REVERSIBLE
See Figure 4.
This tool has the feature of being reversible. The
direction of rotation is controlled by a lever located above
the switch trigger. With your screwdriver held in normal
operating position, the direction of rotation lever should
be positioned to the left of the switch for forward driving
operation. The direction of rotation is in reverse when
the lever is to the right of the switch.
FORWARD
The design of the switch will not permit changing the
direction of rotation while the screwdriver is running.
Release the switch trigger and allow the screwdriver to
stop before changing its direction.
REVERSE
Fig. 4
Note: Your screwdriver will not run unless forward/
reverse lever is pushed fully to the left or right.
INSTALLING/REPLACING
BIT HOLDER AND BITS
See Figure 5.
WARNING:
Your screwdriver should never be connected to a
powersupplywhenyouareassemblingparts,making
adjustments, installing or removing bits, cleaning, or
when not in use. Disconnecting your screwdriver will
prevent accidental starting that could cause serious
personal injury.
■ Unplug your screwdriver.
WARNING:
Failure to unplug your screwdriver could result in
accidental starting causing serious injury.
TO REMOVE MAGNETIC BIT HOLDER:
■ Pull adjusting sleeve. The adjusting sleeve and
adjustable nosepiece come off gear casing as a set.
TO INSTALL OR REPLACE BITS:
■ Install 1/4 in. (6.4 mm) screwdriver bits by inserting
them into magnetic bit holder.
■ Remove magnetic bit holder. Pull bit holder out with
pliers if you cannot remove it by hand.
Note: It is not necessary to remove adjustable
nosepiece to install or remove bits. The magnetic bit
holder shown in figure 5 illustrates the location of bit
holder inside nosepiece.
TO REASSEMBLE BIT HOLDER AND NOSEPIECE:
■ Push bit holder into hex opening of spindle until ball
lock snaps in groove in bit holder shank.
■ Replace 1/4 in. (6.4 mm) screwdriver bits by pulling
them out of magnetic bit holder.
■ Attach adjustable nosepiece to the gear case. Align
raised tab inside the adjustable nosepiece with the
groove on the gear case and push the nosepiece as
far as it will go.
ADJUSTING
SLEEVE
PULL TO REMOVE
ADJUSTABLE NOSEPIECE
1/4 in. (6.4 mm)
SCREWDRIVER
BIT
GEAR CASING
MAGNETIC BIT HOLDER WITH
1/4 in. (6.4 mm) HEX OPENING
ADJUSTABLE
NOSEPIECE
ALIGN AND PUSH TO REPLACE
ADJUSTABLE NOSEPIECE
Fig. 5
9
OPERATION
SETTING DEPTH
See Figure 6.
TO DECREASE DEPTH
OF SCREWDRIVER BIT
The adjustable nosepiece of your tool will automatically
drive screws to preset depths. Make preset depth
adjustments as follows:
■ Unplug your screwdriver.
WARNING:
Failure to unplug your screwdriver could result in
accidental starting causing serious injury.
TO INCREASE DEPTH
OF SCREWDRIVER BIT
■ Rotate adjusting sleeve until you obtain the desired
depth for bit holder or screwdriver bit.
PRESET DEPTH SETTING
OF SCREWDRIVER BIT
■ Test drive a screw in scrap material to determine if it
is correct.
■ Adjust as necessary to increase or decrease the
desired depth.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating your screwdriver. Failure
to do so could result in dust, shavings, loose particles
or foreign objects being thrown into your eyes,
causing possible serious injury.
Fig. 6
DRIVING SCREWS
See Figures 7 and 8.
■ Depress and release the switch trigger to be sure
yourscrewdriverisinOFFpositionbeforeconnecting
it to power supply.
■ Check the direction of rotation lever for correct set-
ting (forward or reverse). See Figure 4.
■ Secure the workpiece. Use clamps if necessary.
■ Plug your screwdriver into power supply source.
■ Depress the switch trigger to start your screwdriver.
Do not lock the switch ON for jobs where your screw-
driver may need to be stopped suddenly.
Fig. 7
■ Hold your screwdriver firmly and place the bit and
screw at the point to be driven.
Note: The bit holder is magnetized and will hold most
commercial drywall screws.
■ Apply quick, snap action type pressure to the
screwdriver bit. The pressure being applied to the
screwdriver bit will engage the clutch and drive the
screw. See Figures 7 and 8.
You will learn from practice and experience. We suggest
that you begin each new job by driving several test
screws in scrap material to check depth setting.
Fig. 8
10
MAINTENANCE
WARNING:
When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause
product damage.
GENERAL
EXTENSION CORDS
All parts represent an important part of the double
insulation system and should be serviced only at an
authorized service center.
The use of any extension cord will cause some loss of
power. To keep the loss to a minimum and to prevent
tool overheating, use an extension cord that is heavy
enough to carry the current the tool will draw.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, carbon dust, etc.
A wire gage size (A.W.G.) of at least 16 is recommended
for an extension cord 100 feet or less in length. When
working outdoors, use an extension cord that is suitable
for outdoor use. The cord's jacket will be marked WA.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline, petro-
leum-based products, penetrating oils, etc. come in
contact with plastic parts. They contain chemicals that
can damage, weaken or destroy plastic.
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged
cord since touching the damaged area could cause
electrical shock resulting in serious injury.
It has been found that electric tools are subject to
accelerated wear and possible premature failure when
theyareusedonfiberglassboats,sportscars,wallboard,
spacklingcompounds,orplaster.Thechipsandgrindings
from these materials are highly abrasive to electric tool
parts, such as bearings, brushes, commutators, etc.
Whenusingthistoolonthesetypematerialsforextended
periods of time, it is extremely important that the tool is
cleaned frequently by blowing with an air jet.
Extension cords suitable for use with your screwdriver
are available at your nearest authorized service center.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high-grade lubricant for the life of the
unit under normal operating conditions. Therefore, no
further lubrication is required.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a dust
mask.
11
OPERATOR'S MANUAL
Drywall Screwdriver
Model No. DSG50
DOUBLE INSULATED
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to
provideallpertinentfactswhenyoucallorvisit.Pleasecall1-800-525-2579intheUnited
States for your nearest Ryobi Authorized Service Center. You can also check our
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBER DSG50
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson SC 29625
Post Office Box 1207
Anderson SC 29622-1207
Phone 1-800-525-2579
983000-042
|