OPERATOR’S MANUAL
HEAT GUN
DOUBLE INSULATED
HG500
Your heat gun has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT SAFETY INSTRUCTIONS
n
Avoid accidental starting. Be sure switch is off
WARNING:
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch on
invites accidents.
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious personal injury.
nRemove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
READ THESE INSTRUCTIONS
WORK AREA
nDo not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
nKeep your work area clean and well lit. Cluttered
nUse safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
nDo not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
benches and dark areas invite accidents.
nDo not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
nDo not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
nKeep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
TOOL USE AND CARE
ELECTRICAL SAFETY
nUse clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
nDo not force tool. Use the correct tool for your appli-
cation. The correct tool will do the job better and safer
at the rate for which it is designed.
nDouble insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation
eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
nDo not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
nDisconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
nStore idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
nMaintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
nCheck for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
nUse only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
n Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
nAvoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
nTo reduce the risk of fire or electric shock, do not ex-
pose this product to rain or moisture. Store indoors.
nDo not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
n
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
nStay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
nDress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
3
IMPORTANT SAFETY INSTRUCTIONS
nWhen servicing a tool, use only identical replacement
SERVICE
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
nTool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
nThe nozzle of the heat gun becomes very hot during nProtect your hearing. Wear hearing protection during
operation and should not be touched until the tool has
cooled. Always hold the tool by the insulated gripping
surface to reduce the risk of serious personal injury.
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
nInspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
nHeat guns produce very high temperatures and must
be used with caution to prevent combustible material
from igniting. Keep tool in constant motion; do not
stop or dwell in one spot. Following this rule will reduce
the risk of fire or serious personal injury.
nCheck damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
nExcessive heat can generate fumes which may be
dangerous when inhaled. Wear a dust respirator mask
or dual filter respirator mask when using the heat gun.
Following this rule will reduce the risk of serious personal
injury.
n Keep a fully charged fire extinguisher close at hand
for emergency use. Following this rule will reduce the
risk of fire or serious injury.
nMake sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 14 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
nDo not leave the heat gun unattended while running or
cooling down. Always set tool on a flat, level surface
so nozzle tip is directed upwards, away from support-
ing surface, while running or cooling down. Following
this rule will reduce the risk of fire or serious injury.
nKnow your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
nSave these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
nAlways wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
WARNING:
Fumes created by heating some materials may contain chemicals known to cause cancer, birth defects, or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well-ventilated area and work with approved safety equipment, such as those masks that
are specially designed to filter out microscopic particles.
4
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Hot Surface
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
To reduce the risk of injury or damage, avoid contact with
any hot surface.
5
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An un-
dersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is desig-
nated with “WA” on the cord’s jacket.
The double insulated system is intended to protect the
user from shock resulting from a break in the tool’s in-
ternal insulation. Observe all normal safety precautions
to avoid electrical shock.
Before using any extension cord, inspect it for loose or ex-
posed wires and cut or worn insulation.
**Ampere rating (on tool faceplate)
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performedonlybyaqualifiedservicetechnician. Forservice,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100'
ELECTRICAL CONNECTION
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
WARNING:
Keep the extension cord clear of the working area. Po-
sition the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged re-
place immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
7
FEATURES
PRODUCT SPECIFICATIONS
Heat Output........................................................................................................................................................ 200˚F-1100˚F
Input .....................................................................................................................................120 V, 60 Hz, AC only, 11 Amps
Net Weight....................................................................................................................................................................2.1 lbs.
LED TEMPERATURE
TEMPERATURE
DISPLAY
ADJUSTMENT DIAL
NOSE CONE
ON/OFF SWITCH
SUPPORT
STAND
HANGER
CONCENTRATOR
NOZZLE
HANDHELD
SCRAPER
SCRAPER NOZZLE
TUBE BENDER
NOZZLE
Fig. 1
8
FEATURES
KNOW YOUR HEAT GUN
TEMPERATURE ADJUST DIAL
Thetemperatureofyourheatguncanbeadjustedfrom200ºF
to 1100ºF by rotating the temperature adjustment dial.
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
LED TEMPERATURE DISPLAY
LED lights located on top of the heat gun display the desired
temperature as indicated by the position of the temperature
adjustment dial.
ON/OFF SWITCH
Your heat gun has a conveniently located on/off slide
switch.
POWER CORD
NOSE CONE
An extra-long 10-foot power cord gives you more freedom
of movement and placement flexibility when working with
your heat gun.
The nose cone on your heat gun can be removed for work
in confined spaces.
SUPPORT STAND
Your heat gun has a built-in support stand for ease of use
and convenient cool down.
HANGER
A hanger is located in the support stand of your heat gun.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
WARNING:
n Do not discard the packing material until you have care-
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Heat Gun
Scraper Nozzle
WARNING:
Tube Bender Nozzle
Concentrator Nozzle
Handheld Scraper
Case
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
Operator’s Manual
Warranty Registration Card
9
OPERATION
Persons removing paint should follow these guidelines:
WARNING:
nMove the workpiece outdoors. If this is not possible, keep
the work area well ventilated. Open the windows and put
an exhaust fan in one of them. Be sure the fan is moving
the air from inside to outside.
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
nRemove or cover any carpets, rugs, furniture, clothing,
cooking utensils, and air ducts.
WARNING:
nPlace drop cloths in the work area to catch any paint chips
or peelings. Wear protective clothing such as extra work
shirts, overalls, and hats.
Always wear safety goggles or safety glasses with side
shields, a dust respirator mask or dual filter respirator
mask, and protective gloves when operating the heat gun.
Failure to do so could result in possible serious injury.
nWork in one room at a time. Furnishings should be re-
moved or placed in the center of the room and covered.
Work areas should be sealed off from the rest of the
dwelling by sealing doorways with drop cloths.
WARNING:
nChildren, pregnant or potentially pregnant women, and
nursing mothers should not be present in the work area
until the work is done and all clean up is complete.
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of
attachments or accessories not recommended can result
in serious personal injury.
nWear a dust respirator mask or a dual filter (dust and
fume) respirator mask which has been approved by the
Occupational Safety and Health Administration (OSHA),
the National Institute of Safety and Health (NIOSH), or
the United States Bureau of Mines. These masks and
replaceable filters are readily available at major hardware
stores. Be sure the mask fits. Beards and facial hair may
keep masks from sealing properly. Change filters often.
DISPOSABLE PAPER MASKS ARE NOT ADEQUATE.
APPLICATIONS
You may use this tool for the purposes listed below:
nSoften paint, caulking and putty for easier removal
n Soften adhesives to help remove stickers, floor tiles,
wallpaper, etc.
n Heating plastic and metal for bending
nSoldering pipe joints
nUse caution when operating the heat gun. Keep the heat
gun moving as excessive heat will generate fumes
nKeep food and drink out of the work area. Wash hands,
arms and face and rinse mouth before eating or drink-
ing. Do not smoke or chew gum or tobacco in the work
area.
n Shrink tubing for electrical work
n Shrink plastic film for wrapping or weatherproofing
n Loosen rusted nuts, bolts, and fittings
nClean up all removed paint and dust by wet mopping the
floors. Use a wet cloth to clean all walls, sills, and any
other surface where paint or dust is clinging. DO NOT
SWEEP, DRY DUST, OR VACUUM. Use a high phosphate
detergent or trisodium phosphate (TSP) to wash and mop
areas.
READ THIS INSTRUCTION
WARNING:
Use extreme care when stripping paint. The peelings,
residue, and vapors of paint may contain lead, which
is poisonous. Any pre-1977 paint may contain lead and
paint applied to homes prior to 1950 is likely to contain
lead. Once deposited on surfaces, hand to mouth contact
can result in the ingestion of lead. Exposure to even low
levels of lead can cause irreversible brain and nervous
system damage; young and unborn children are par-
ticularly vulnerable. Before beginning any paint removal
process, you should determine whether the paint you are
removing contains lead. This can be done by your local
health department or by a professional who uses a paint
analyzer to check lead content of the paint to be removed.
LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY
A PROFESSIONAL AND SHOULD NOT BE REMOVED
USING A HEAT GUN.
nAt the end of work session, put the paint chips and debris
in a double plastic bag, close it with tape or twist ties,
and dispose of properly.
nRemove protective clothing and work shoes in the work
area to avoid carrying dust into the rest of the dwelling.
Wash work clothes separately. Wipe shoes off with a wet
rag that is then washed with the work clothes. Wash hair
and body thoroughly with soap and water.
10
OPERATION
WARNING:
This heat gun generates extremely high temperatures.
Hidden areas such as behind walls, ceilings, floors, soffit
boards, and other panels may contain flammable materi-
als that could be ignited by the heat gun when working
in these locations. Keep tool in constant motion; do not
stop or dwell in one spot as the panel or material behind
it may ignite. The ignition of these materials may not be
readily apparent and could result in property damage and
injury to persons.
SWITCH IN
ON POSITION
SAVE THIS INSTRUCTION
SWITCH IN
OFF POSITION
WARNING:
Do not direct hot tip or nozzle toward clothing, hands
or other body parts. Intense heat from tip or nozzle can
cause serious burns or cause clothing to ignite.
Fig. 2
LED TEMPERATURE
DISPLAY
SAVE THIS INSTRUCTION
STARTING/STOPPING THE HEAT GUN
See Figure 2.
The heat gun is started by sliding the on/off switch up to
the ON (l) position. To stop, slide the switch down to the
OFF (O) position.
ADJUSTING THE TEMPERATURE
See Figure 3.
The temperature of the heat gun is controlled by the tem-
perature adjustment dial located at the top of the tool. Turn
the dial to the right to raise the temperature and to the left
to lower the temperature. The LED lights located in front of
the dial indicate the temperature setting selected.
TEMPERATURE
ADJUST DIAL
NOTE: The proper amount of heat necessary for a specific
applicationdependsonthedistancebetweenthenozzleand
workpiece and the length of time heat is applied. Experiment
with scrap materials and start with the lowest temperature
range. Be cautious when working until the proper combina-
tion of heat, distance and time has been determined.
Fig. 3
HANDS-FREE OPERATION
See Figure 4.
The heat gun has a flat bottom surface that acts as a sup-
port stand to allow hands-free operation and cooling. Rest
the tool on a flat surface and make sure the cord placement
does not cause the heat gun to tip over.
NOTE: Do not leave heat gun unattended while it is running
or cooling down. Always set on a flat, level surface with noz-
zle tip directed upwards, away from supporting surface.
SUPPORT STAND
Fig. 4
11
OPERATION
INSTALLING ATTACHMENTS
See Figures 5 - 6.
HEAT GUN NOZZLE
Severalattachmentsareincludedwiththeheatguntoexpand
its capabilities. Attachments are installed simply by placing
them on the end of the heat gun’s nozzle.
NOTE: Install or remove attachments only when both the
heat gun nozzle and the attachment nozzle are cool.
Scraper nozzle: The scraper nozzle reduces the airflow
from a circular area to a wide, narrow line. This nozzle can
be used along with the handheld scraper to remove paint.
It can also be used for softening and forming acrylic sheets,
vinyl floor tiles, linoleum, and laminate surfaces.
Tube bender nozzle: The tube bender nozzle is useful
for surround bending, soldering pipe, and applying heat to
shrinkable tubing.
ATTACHMENT
NOZZLE
Fig. 5
Concentrator nozzle: The concentrator nozzle intensifies
the application of heat in a specific area. Uses for this nozzle
include bending acrylic plastic sheets, soldering pipe joints,
and directing heat into corners.
TUBE BENDER NOZZLE
REMOVING THE NOSE CONE
CONCENTRATOR
NOZZLE
See Figure 7.
SCRAPER
NOZZLE
The nose cone helps to limit exposure to the extremely hot
nozzlewhentheheatgunisinuse.However,thenoseconecan
be removed to allow use of the heat gun in tight spaces.
NOTE: Always reinstall the nose cone when finished.
To remove:
Fig. 6
n Unplug the heat gun.
n With nozzle pointed away from you, rotate the nose cone
slightly clockwise and remove.
NOSE
CONE
WARNING:
The nozzle of the heat gun is extremely hot during use.
It will stay hot for several minutes, depending on room
temperature. Allow heat gun to cool before attempting to
install or remove the nose cone to avoid possible serious
personal injury.
To reinstall:
n Unplug the heat gun.
HEAT GUN
NOZZLE
Fig. 7
nSlide nose cone over the heat gun nozzle.
nSeat the nose cone against the body of the heat gun by
aligning tabs on heat gun body to notches on base of
nose cone.
nRotate the nose cone counterclockwise to secure.
USING THE HANGER
See Figure 8.
The heat gun has a hanger recessed into the support stand.
To use, simply slide your finger into the opening underneath
the hanger and flip the hanger out and away from the sup-
port stand.
HANGER
Fig. 8
12
MAINTENANCE
WARNING:
WARNING:
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
Always unplug the heat gun before performing any type
of maintenance. Following this rule will reduce the risk
of serious personal injury.
CLEANING THE HEAT GUN
WARNING:
The heat gun and attachments should be kept clean, dry,
and free of oil or grease. Only a mild soap and damp cloth
should be used to clean the heat gun. Do not allow liquid
to enter the tool.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
The high temperatures of the heat gun will cause the nozzle
to turn dark over time. This is normal and will not affect its
performance or life.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Ventilation openings must be kept clean and free of foreign
matter. The most effective method of cleaning the vents is
with compressed air. Do not attempt to clean by inserting
pointed objects through the openings.
WARNING:
STORAGE
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Always allow the heat gun and nozzle attachments to cool
to room temperature before storing. Store the heat gun out
of reach of children and untrained individuals.
WARNING:
Electrictoolsusedonfiberglassmaterial,wallboard,spackling
compounds, or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips and
grindings are highly abrasive to bearings, brushes, commu-
tators,etc.Consequently,wedonotrecommendedusingthis
toolforextendedworkonthesetypesofmaterials. However,
if you do work with any of these materials, it is extremely
important to clean the tool using compressed air.
The nozzle of the heat gun will stay hot for several minutes
after use. Always allow heat gun to cool before storage.
Following this rule will reduce the risk of serious personal
injury or property damage.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
13
OPERATOR’S MANUAL
HEAT GUN
DOUBLE INSULATED
HG500
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
HG500
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
Phone 1-800-525-2579
983000-564
10-04
|