RF-TVMFM01_10-0451_QSG_V2_EN_finalLR.pdf
1
8/23/2011 11:56:36 AM
QUICK SETUP GUIDE
1 Install the arm assembly
2 Attach the mounting hardware
RF-TVMFM01
Option 1: Installing to a wood stud wall
Note: Any material covering the wall must not exceed 16 mm (5/8 in.).
1 Locate the stud. Verify the center of the stud with an awl or
thin nail or use an edge-to-edge stud ꢀnder.
2 Level the arm assembly (A) and mark the hole locations.
3 Drill pilot hole to a depth of 75 mm (3 in.) using a
5.5 mm (7/32 in.) diameter drill bit.
Option 1: For TVs with inset mounting or that require extra space for wires
Install spacers (E), washers (D), and screws (C) into the top two holes in the back of the TV.
Leave a gap between the spacer and the washer and screw.
Note: Only install the hardware in the top two screw holes at this time. The remaining hardware
will be installed in Step 3.
<16 mm
(5/8 in.)
4 Align the arm assembly (A) with the
pilotholes, insertthecoachscrews(G)
through the holes in the arm
assembly, then tighten
the coachscrews only until
they are pulled ꢀrmly
against the arm assembly.
CAUTION: Avoid potential
injuries or property damage!
DO NOT over-tighten the
coachscrews (G).
Thank you for choosing the Rocketꢀsh RF-TVMFM01.
The RF-TVMFM01 TV mount is designed to support a
ꢁat-panel TV weighing up to 15.8 kg (35 lbs.).
75 mm
(3 in.)
Wall
203.2 mm
(8 in.)
TV
Gap
139.7 mm
(5-1/2 in.)
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
TV shifts 139.7 mm (5-1/2 in.) in. from the
home position to full extension.
Package contents
A Arm assembly (1)
Option 2: Installing to a solid concrete or concrete block wall
1 Level the arm assembly (A) and mark the hole locations.
2 Drill pilot hole to a depth of 75 mm (3 in.) using a
9.5 mm (3/8 in.) diameter drill bit.
3 Insert the concrete wall anchors (H) into the pilot holes
and make sure that the anchors are seated ꢁush with
the concrete surface.
Option 2: For ꢀat backed TVs
M4 bag
Install washers (D), and screws (B) into the top two holes in the back of the TV.
Leave a gap between the back of the TV and the washer and screw.
Note: Only install the hardware in the top two screw holes at this time. The remaining hardware
will be installed in Step 3.
B M4 × 12 mm screws (4)
C M4 × 30 mm screws (4)
D M4 washers (4)
E M4 spacers (4)
4 Align the arm assembly (A) with the anchors, insert
the coachscrews (G) through the holes in the arm assembly,
then tighten the coachscrews only until they are pulled
ꢀrmly against the arm assembly.
CAUTION: To prevent property
damage or personal injury, never
drill into mortar between blocks.
Mount wall plate directly onto the
concrete surface.
Hex key bag
F 4 mm (5/32 in.) hex key (1)
M4 bag
M4 × 12 mm
Coach Screw bag
CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the coachscrews (G).
G 8 mm (5/16 in.)× 70 mm
(2 3/4 in.) coach screw (2)
H Concrete anchor (2)
M4 × 30 mm
Cable ties
M4
M4
Hex key bag
Lag Bolt Bag
4 mm
(5/32 in.)
8mm (5/16 in.)× 70 mm (2 3/4 in.)
Gap
Cable ties
75 mm
(3 in.)
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
Tools you will need:
• Stud finder
• Socket wrench with
• Awl
• Pencil
12.7 mm (1/2 in.) socket
or adjustable wrench
• Level
• 5.5 mm (7/32 in.) wood drill bit
• 9.5 mm (3/8in.) masonry drill bit
(concrete only)
• Tape measure
• Phillips screwdriver
• Hammer (concrete only)
• Power drill
|