12-2014.fm Page 1 Tuesday, May 9, 2000 8:51 AM
XL-110 High Power
Stereo Amplifier
12-2014.fm Page 3 Tuesday, May 9, 2000 8:51 AM
ˆ Features
Your RadioShack High-Power Stereo Amplifi-
er produces a total of 110 watts to give add-
ed punch and power to your vehicle’s
existing auto sound system.
Hz. This lets you set up the amplifier so you
can connect a subwoofer.
Short Circuit Protection
— distorts the am-
plifier’s sound if any output channel shorts,
alerting you to turn off the auto sound sys-
tem.
The amplifier produces up to 55 watts per
channel of clean, powerful sound at all audio
frequencies with minimum distortion. You
can connect your auto sound system’s low-
level or speaker-level outputs to this amplifi-
er.
Auto-Off
— protects the amplifier by tempo-
rarily shutting down if it gets too hot, an out-
put channel shorts, or it detects an input
overload. The amplifier restarts automatically
when it cools or the problem is corrected.
Its features include:
14K Gold-Plated Noise-Isolated Low-Lev-
Protection Indicator
— lights if the amplifier
el Input Jacks
— let you connect low-level
shuts itself down.
(preamplifier) signal inputs to match your
auto sound system’s output for the best
high-fidelity performance.
THE FCC WANTS YOU TO
KNOW
14K Gold-Plated Speaker Terminals
— de-
Your amplifier might cause TV or radio inter-
ference even when it is operating properly.
To determine whether your amplifier is caus-
ing the interference, turn off your amplifier. If
the interference goes away, your amplifier is
causing it. Try to eliminate the interference
by:
signed for low impedance, high conductivity,
and minimum corrosion, to provide the high-
est signal transfer and lowest sound distor-
tion.
Input Level Control
— lets you adjust the
level of the audio signals that enter the am-
plifier.
• Moving your amplifier away from the
receiver
Automatic Power Switching
— can auto-
matically turn the amplifier on or off when
you turn your auto sound system on or off
(depending on how you hook up the amplifi-
er).
• Contacting your local RadioShack store
for help
Mute Turn On Circuit —
eliminates the
thump you hear when you turn on some am-
plifiers.
Power Indicator
— lights when power is
supplied to the amplifier.
Crossover Frequency Circuit
— lets you
adjust the crossover frequency from 45−400
3
Features
12-2014.fm Page 4 Tuesday, May 9, 2000 8:51 AM
ˆ Preparation
SUPPLIED HARDWARE
Your amplifier comes with the following items. Be sure you locate everything listed before you
store or dispose of the packing materials.
Power Wire (Red) (1)
Ground Wire (Black) (1)
Remote Wire (Blue/White) (1)
Flat Washers (4)
4-Pin Connector with Wire (1)
Sheet Metal Screws (4)
Twist-On
Terminal
Connectors (5)
Lock Washers (4)
Also, be aware that installation in your vehi-
cle might require cutting or modifying your
vehicle.
BEFORE YOU BEGIN THE
INSTALLATION
Before you install your amplifier, read all the
instructions in this owner’s manual. You
should be able to answer all of these ques-
tions about your vehicle’s electrical and auto
sound systems.
Choosing a Mounting Location
A good location for mounting the amplifier is
in your vehicle’s trunk. Wherever you decide
to mount it, choose a mounting location that:
• Does my vehicle have an auto sound
system, such as a car stereo or CD
player, already installed? (You must
have an existing auto sound system to
use this amplifier.)
• does not interfere with the vehicle’s
operation
• lets you drill mounting holes without
damaging other vehicle components
• How do I connect a wire to the fuse box?
• allows enough space around the cooling
fins for proper airflow and cooling
• Which of the auto sound system’s wires
is the power wire?
• lets you easily see the amplifier’s
POWER and PROTECTION indicators
• Which of the auto sound system’s termi-
nals are low-level outputs and which are
high-level (speaker) outputs?
4
Preparation
12-2014.fm Page 5 Tuesday, May 9, 2000 8:51 AM
Warning:
The amplifier gets very hot while it
Then test the connections. When you con-
firm that everything works as expected, dis-
connect the amplifier, mount it in your
vehicle, and reconnect it.
is on. Do not touch the amplifier or place
flammable objects near it while it is on.
Preparing the Mounting Area
Caution:
If you do not make the connections
in the order shown, damage to the amplifier
and your auto sound system is possible if
any wire connections are made incorrectly.
In addition to the supplied hardware, you
need these materials:
• an adapter harness
• additional wire
Note:
For easier installation, mark each wire
you plan to connect with the name of the ter-
minal you will connect it to.
• shielded audio cables
BEFORE YOU MAKE THE
CONNECTIONS
• 16- or 18-gauge marked or color-coded
wire.
The supplied connection cables include all
the lead wires you need to connect the am-
plifier to ground, power, and your existing
auto sound system.
Confirm that the amplifier fits in your vehi-
cle’s available mounting area. This amplifier
requires a 51/2-inch high by 93/4-inch wide by
113/4-inch deep (13.9 × 23.5 × 29.8 cm)
mounting area.
Important:
Routing Cables and Wires
• Do not cut any of the supplied wires. If
you cut any wire, you cannot obtain a
refund or exchange on this product.
However, RadioShack will provide war-
ranty service if you cut a wire and find
the product is defective.
Avoid routing the connection cables and any
speaker wires near moving parts or sharp
edges. You can usually route wires and ca-
bles along the wiring channel beneath the
vehicle’s door facings by carefully removing
the molding that holds the carpet in place. Af-
ter routing the cables and wires, replace the
molding.
• If the connectors on your vehicle’s auto
sound system are not compatible with
the amplifier’s connectors, you might
need an adapter harness to complete
the connections. Your local RadioShack
store has adapter harnesses for most
vehicles.
INSTALLATION ORDER
For trouble-free installation, simply follow the
sections in this owner’s manual in order.
First, make all the connections temporarily
by connecting the amplifier to:
You might need additional wire, depending
on your individual auto sound system, to
complete the connections. Your local Ra-
dioShack store has a variety of wire and wire
accessories.
1
2
3
Ground and power
Your auto sound system’s outputs
Your speakers
5
Preparation
12-2014.fm Page 6 Tuesday, May 9, 2000 8:51 AM
Cautions:
per channel). Each speaker must have
an impedance of at least 4 ohms. Your
local RadioShack store has a large vari-
ety of speakers.
• For added safety and to protect your
amplifier and auto sound system, dis-
connect the cable from your vehicle’s
–
negative ( ) battery terminal before you
begin.
To make it easier to gauge wire length and
connect the amplifier, temporarily place the
amplifier as close as possible to the selected
mounting location.
• Be sure your speakers can handle as
much as 110 watts of power (55 watts
CONNECTING GROUND AND SWITCHED/PRIMARY POWER
Blue/White
AMP Remote Turn On
Black
Vehicle’s Battery
Chassis
Ground
Switched Power Lead
Auto Sound System
Follow these steps to connect the amplifier to
ground, switched power, and primary power.
vehicle’s frame. Be sure the bolt is not
insulated from the chassis by a plastic
part.
1. If you have not done so already, discon-
nect the cable from your vehicle’s nega-
4. Use a screwdriver to connect the spade
end of the supplied blue/white wire to
–
tive ( ) battery terminal.
REM
the amplifier’s
minal.
(remote power) ter-
2. Use a screwdriver to connect the spade
end of the supplied black ground wire to
GND
a
the amplifier’s
(ground) terminal.
5.
If your auto sound system has
switched power lead, connect the blue/
white wire’s other end to your auto
sound system’s switched power lead
3. Connect the black ground wire’s other
end to a chassis ground, such as a
metal bolt attached to a metal part of the
6
Preparation
12-2014.fm Page 7 Tuesday, May 9, 2000 8:51 AM
using one of the supplied twist-on termi-
nal connectors.
This connection turns on the amplifier
when you turn on the auto sound sys-
tem, and turns off the amplifier when
you turn off the auto sound system. This
prevents your vehicle’s battery from
being drained if you leave your amplifier
on when you turn your auto sound sys-
tem off.
If your auto sound system does not have
a switched power lead, connect the
blue/white wire’s other end to a point in
your vehicle’s fuse block that has power
only when you turn on the ignition or turn
the key to ACC.
This connection turns on the amplifier
when you turn on the ignition or turn the
key to ACC, and turns off the amplifier
when you turn off the ignition. This pre-
vents your vehicle’s battery from being
drained if you leave your amplifier on
when you turn off the ignition.
6. Use a screwdriver to connect the spade
end of the supplied red power cable
(with in-line fuse holder) to the ampli-
+ 12V
fier’s
terminal.
7. Connect the other end of the red power
+
cable to your vehicle’s positive ( ) bat-
tery terminal. Then tighten the terminal.
Caution:
Due to the amplifier’s high cur-
rent requirement, you must connect the
red power cable’s fused end directly to
the vehicle’s positive (+) battery terminal
or damage to your vehicle’s wiring could
result.
Do not reconnect your vehicle’s negative (–)
battery cable yet.
7
Preparation
12-2014.fm Page 8 Tuesday, May 9, 2000 8:51 AM
ˆ Connecting Inputs
LOW-LEVEL INPUTS
You can connect your auto sound system’s low-level line out jacks to the amplifier’s low-level
line in jacks.
If your auto sound system does not have low-level line out jacks, see “High-Level (Speaker
Wire) Inputs” on Page 9 to connect your amplifier.
Note:
For the best results, use shielded audio cables (not supplied) available at your local Ra-
dioShack store.
1. Temporarily place the amplifier as close as possible to the selected mounting location.
2. If your auto sound system has two line out jacks, connect the auto sound system to the
amplifier as shown:
Right
Left
Auto Sound System
Note: If your auto sound system has four separate line out jacks
, use the auto sound sys-
tem’s front left and right jacks to make this connection.
8
Connecting Inputs
12-2014.fm Page 9 Tuesday, May 9, 2000 8:51 AM
Note:
A floating ground connection lets the
HIGH-LEVEL (SPEAKER
WIRE) INPUTS
amplifier provide more power to each speak-
er, but requires that you connect a separate
wire to each speaker terminal. A common
ground connection lets you use fewer wires
to connect the speakers to the amplifier, but
reduces the amount of power supplied to the
speakers from the amplifier.
If your auto sound system does not have
low-level line out jacks but has only speaker
outputs, connect your auto sound system’s
HIGH IN-
speaker outputs to the amplifier’s
PUT
jacks.
Use the supplied wire harness and the sup-
plied twist-on terminal connectors to make
the appropriate connections.
• If your auto sound system has four
speaker outputs, see “Four Speaker
Outputs” on Page 10 to connect your
system’s speaker outputs to the ampli-
fier using either a floating or common
ground connection.
• If your auto sound system has two
speaker outputs, see “Two Speaker Out-
puts” on Page 11 to connect your sys-
tem’s speaker outputs to the amplifier
using either
a
floating or common
ground connection.
9
Connecting Inputs
12-2014.fm Page 10 Tuesday, May 9, 2000 8:51 AM
Four Speaker Outputs
Floating Ground Connection
White/Black
Gray/Black
Right Front
Speaker
Left Front
Speaker
Auto Sound System
Common Ground Connection
Right Front
Speaker
Left Front
Speaker
Auto Sound System
10
Connecting Inputs
12-2014.fm Page 11 Tuesday, May 9, 2000 8:51 AM
Two Speaker Outputs
Floating Ground Connection
Gray/Black
White/Black
Auto Sound System
Common Ground Connection
Auto Sound System
11
Connecting Inputs
12-2014.fm Page 12 Tuesday, May 9, 2000 8:51 AM
CONNECTING SPEAKERS
You can connect two speakers or a subwoof-
er to the amplifier and your auto sound sys-
tem.
2. Separate each wire’s two conductors at
both ends for a length of about 4 inches.
3. Strip the insulation from the ends of
each conductor to expose 1/4 inch of
wire. Twist the ends to secure loose
strands.
• If you are connecting two speakers, fol-
low Steps 1–3 under “Preparing the
Speaker Wires” then see “Connecting
Two Speakers” on Page 13 to connect
the speakers to the amplifier.
Conductors
1/4
Inch
• If you are connecting a subwoofer, follow
Steps 1–3 under “Preparing the Speaker
Wires” then see “Connecting a Sub-
woofer” on Page 13 to connect a sub-
woofer to the amplifier.
4 Inches
Preparing the Speaker Wires
Caution:
You must connect a separate wire
to each speaker terminal as described in the
following procedures. Unless your auto
sound system’s speakers use a common
ground wire, do not use a common wire or
chassis ground for speaker connections.
Notes:
• We recommend you use 16- or 18-
gauge marked or color-coded wires to
help you correctly connect the speakers
to your amplifier.
• Color-coded wires have a stripe running
down one of the conductors or different
colored insulation for each conductor.
Your local RadioShack store has a wide
selection of speaker wire to choose
from.
• For the maximum bass response and
the best overall performance, keep your
speakers properly phased (connect + to
+ and – to –).
1. With the speakers placed in their
approximate locations, run one wire
from each speaker to the amplifier.
12
Connecting Inputs
12-2014.fm Page 13 Tuesday, May 9, 2000 8:51 AM
Connecting Two Speakers
Right Speaker
Left Speaker
1. Use a screwdriver to connect the left speaker’s positive (+) wire to the amplifier’s
SPEAKER L (+)
terminal.
2. Use a screwdriver to connect the left speaker’s negative (–) wire to the amplifier’s
SPEAKER L (–)
terminal.
3. Repeat Steps 1–2 to connect the right speaker’s positive (+) and negative (–) wires to the
SPEAKER R (+)
SPEAKER R (–)
terminals.
amplifier’s
and
Connecting a Subwoofer
Or
Subwoofer
Subwoofer
SPEAKER
1. Use a screwdriver to connect the subwoofer’s positive (+) wire to the amplifier’s
L (+)
SPEAKER R (+)
terminal.
or
13
Connecting Inputs
12-2014.fm Page 14 Tuesday, May 9, 2000 8:51 AM
2. Use a screwdriver to connect the sub-
woofer’s positive (+) wire to the ampli-
–
SPEAKER L (+)
terminal, connect
woofer’s negative ( ) wire to the ampli-
fier’s
–
fier’s negative (–) terminal for the same
channel you connected in Step 1. For
example, if you connected the sub-
the subwoofer’s negative ( ) wire to the
SPEAKER L (–)
amplifier’s
terminal.
ˆ Completing the Installation
system operate properly. The amplifier turns
on after a few seconds.
TESTING THE
CONNECTIONS
If you cannot quickly confirm whether the
auto sound system and amplifier are working
Before you continue, make sure you have
securely made all connections. Then recon-
turn off your vehicle’s ignition
properly,
–
nect the cable to the vehicle’s negative ( )
and disconnect the cable from your vehi-
battery terminal.
cle’s negative (–) battery terminal.
Then
recheck your connections.
LEVEL (MIN/MAX)
Set
on the side of the am-
plifier to its mid position (see “Adjusting the
Audio Level” on Page 15). Then turn on your
vehicle’s ignition and auto sound system to
confirm that the amplifier and auto sound
After you test the auto sound system and
amplifier and verify that everything is proper-
ly connected and working, follow the instruc-
tions in “Mounting the Amplifier.”
MOUNTING THE AMPLIFIER
Sheet Metal Screw
Lock Washer
Flat Washer
9/64-Inch Mounting Holes
Once you verify that the amplifier is connect-
ed properly, follow these steps to mount it.
2. To make mounting more convenient,
temporarily disconnect the amplifier’s
connections (ground, primary power,
remote power, your auto sound system’s
input, and speakers).
1. Disconnect the cable from the vehicle’s
negative (–) battery terminal.
14
Completing the Installation
12-2014.fm Page 15 Tuesday, May 9, 2000 8:51 AM
Note:
If you have not already done so,
5. Secure the amplifier to the mounting
surface using the supplied sheet metal
screws and washers.
be sure to mark each wire with the name
of the terminal you will reconnect it to.
3. Using the mounting holes on the ampli-
fier as a guide, mark the positions for the
mounting holes.
6. Reconnect the wiring.
7. Reconnect the cable to the vehicle bat-
tery’s negative (–) terminal.
4. Drill 9/64-inch (3.57 mm) holes at the
marked locations, being careful not to
damage anything behind the mounting
surface.
8. Reset your vehicle’s clock, your auto
sound system’s tuner memory, and
other timer/memory devices.
ˆ Operation
TURNING ON THE
AMPLIFIER
ADJUSTING THE AUDIO
LEVEL
LEV-
For the best performance, you must set
The amplifier automatically turns on a few
seconds after you turn your vehicle’s ignition
switch to ACC or ON or turn on your auto
sound system, depending on how you wired
EL (MIN/MAX)
on the amplifier to adjust the
level of the audio signals that enter the am-
plifier.
POWER
the system. The
indicator lights
LEVEL (MIN/
1. Use a screwdriver to turn
when the amplifier is on.
MAX)
MIN
.
fully counterclockwise to
POWER
Indicator
Important:
Your amplifier requires 17 amps
or more of power from your vehicle’s battery
during operation. To protect your battery
from discharging, do not operate the amplifi-
er unless your vehicle is running.
2. Turn up the auto sound system’s volume
control to about one-third of its full
range.
Note:
Your amplifier temporarily shuts down
LEVEL (MIN/MAX)
3. Adjust
to a comfort-
if it gets too hot, then restarts automatically
once it cools.
able listening level.
15
Operation
12-2014.fm Page 16 Tuesday, May 9, 2000 8:51 AM
4. Turn up the auto sound system’s volume
control until the sound begins to distort.
Then immediately turn the volume down
to a point just before where the distor-
tion began.
ADJUSTING FREQUENCY
CROSSOVER
If you installed a subwoofer using the steps
in “Connecting a Subwoofer” on Page 13, set
X-OVER FREQ ON/OFF
ON
X-
to
, then adjust
Caution:
Never turn up the auto sound
OVER FREQ
for your particular vehicle’s
system’s volume control more than
needed to adjust the audio level, or
more than two-thirds of its maximum vol-
ume.
acoustics. The amplifier passes through all
frequencies at or below that setting (45−400
Hz).
LEVEL (MIN/MAX)
5. Adjust
until the sound
is at the maximum level you want the
amplifier to produce.
6. Adjust the auto sound system’s volume
control to a comfortable listening level.
Note: X-OVER FREQ
selects the limit at which
the amplifier will pass frequencies (from 45−
400 Hz). You should not use it to adjust the
sound you hear through your main speakers.
ˆ Troubleshooting
We do not expect you to have any problems with your amplifier, but if you do, these sugges-
tions might help.
Symptom
Possible Cause
Power problem.
Suggestion
No power — the amplifier’s
POWER indicator does not light
after you turn on the vehicle’s
auto sound system.
Check the amplifier’s and auto-
sound system’s fuses and
replace them if necessary (see
“Replacing a Fuse” on
Page 18).
Vehicle’s ignition is not turned
on.
Turn on the ignition.
The amplifier is not properly
connected to your auto sound
system/vehicle.
Check all connections.
No sound.
The auto sound system is not
Turn on the auto sound system
turned on or the volume is set to or adjust its volume.
minimum.
LEVEL (MIN/MAX)
LEVEL (MIN/MAX)
.
is set to
Adjust
minimum.
16
Troubleshooting
12-2014.fm Page 17 Tuesday, May 9, 2000 8:51 AM
Symptom
Possible Cause
Suggestion
No Sound (continued).
The amplifier is not properly
connected to your auto sound
system/vehicle.
Check all connections.
The amplifier might have shut
down.
Turn off your auto sound system
and let the amplifier cool. Make
sure the amplifier is properly
ventilated. Then turn your auto
sound system back on. The
amplifier turns on when it cools
off enough. Or, the amplifier
might have detected an input
overload. Reduce the auto
sound system’s volume.
Power problem.
Check the amplifier’s and auto
sound system’s fuses and
replace them if necessary (see
“Replacing a Fuse” on
Page 18).
Distorted sound.
The amplifier might be receiving Reduce your auto sound sys-
too much input power from your tem’s output power (if possi-
auto sound system.
ble), or reduce the auto sound
system’s volume.
An output channel might have
shorted.
Take the amplifier to your local
RadioShack store.
The amplifier might have shut
down.
Turn off your auto sound system
and let the amplifier cool. Make
sure the amplifier is properly
ventilated. Then turn your auto
sound system back on. The
amplifier turns on when it cools
off enough.
The amplifier’s PROTECTION
indicator lights.
The amplifier is not properly
connected to your auto sound
system/vehicle.
Check all connections.
The amplifier might be receiving Reduce your auto sound sys-
too much power from your auto tem’s output power (if possi-
sound system.
ble), or reduce the auto sound
system’s volume.
If you still have problems, disconnect the amplifier and take it to your local RadioShack store
for assistance.
17
Troubleshooting
12-2014.fm Page 18 Tuesday, May 9, 2000 8:51 AM
ˆ Care
To enjoy your amplifier for a long time:
until they spring apart. Then remove the
fuse.
• Keep the amplifier dry. If it gets wet,
wipe it dry immediately.
• Use and store the amplifier only in nor-
mal temperature environments.
Fuse
• Handle the amplifier gently and care-
fully. Do not drop it.
3. If the fuse is blown, replace it. Use only
an SFE-type fuse with the proper rating.
The fuse must be 20 amps.
• Keep the amplifier away from dust and
dirt.
• Wipe the amplifier with a damp cloth
occasionally to keep it looking new.
4. Reassemble the fuse holder by inserting
the fuse into the longer of the fuse
holder’s ends, and pushing together and
twisting the two parts until they latch
together.
Modifying or tampering with the amplifier’s
internal components can cause a malfunc-
tion and might invalidate its warranty and
void your FCC authorization to operate it. If
your amplifier is not performing as it should,
take it to your local RadioShack store for as-
sistance.
5. Reconnect the cable to the vehicle’s
negative (–) battery terminal.
Replacing the Blade-Type Fuse
REPLACING A FUSE
1. Disconnect the cable from the vehicles
negative (–) battery terminal.
If the amplifier does not operate, you might
need to replace the red power cable’s 20-
amp SFE-type fuse or the 20-amp blade-type
fuse on the amplifier’s back panel. Check
both fuses.
2. Grasp the fuse’s plastic end and pull it
out.
Important:
Let the amplifier cool down and
see if it starts again before you assume a
fuse needs to be replaced.
Caution:
Do not use a fuse with ratings other
than those specified here. Doing so might
damage your amplifier.
3. If the fuse is blown, replace it. Use only
a blade-type fuse with the proper rating.
The fuse must be 20 amps.
Replacing the SFE-Type Fuse
4. Grasp the new fuse’s plastic end and
push it in.
1. Disconnect the cable from the vehicle’s
negative (–) battery terminal.
5. Reconnect the cable to the vehicle’s
negative (–) battery terminal.
2. Push together and twist the fuse
holder’s parts on the red power cable
18
Care
12-2014.fm Page 19 Tuesday, May 9, 2000 8:51 AM
ˆ Specifications
Output Power @ 14.4 VDC 1kHz ..................................... 35 Watts × 2 @ 4 Ohms, 20–20 kHz, 0.5% THD
55 Watts × 2 @ 4 Ohms, 20–20 kHz, 10% THD
40 Watts × 2 @ 2 Ohms, 20–20 kHz, 1% THD
Frequency Response ................................................................................................ 20–20,000 Hz (±3 dB)
Power Supply Voltage ...................................................................................... 14.4 VDC Negative Ground
Maximum Current Draw ........................................................................................................................ 20 A
Dimensions (HWD) ................................................................................................. 21/16 × 9 × 109/16 Inches
(5.2 × 23 × 26.8 cm)
Net Weight .................................................................................................................................. 3 lbs, 15 oz
(1.4 kg)
Specifications are typical; individual units might vary. Specifications are subject to change and improve-
ment without notice.
19
Specifications
12-2014.fm Page 20 Tuesday, May 9, 2000 8:51 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
12-2014
05A00
Printed in China
|