900 MHz Cordless Telephone
with Digital Answering System
4. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
home, consult your local power
company.
13. Do not allow anything to rest on the
power cord. Do not locate this product
where the cord will be stepped on.
5. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
14. Do not overload wall outlets and
extension cords as this can result in a
risk of fire or electric shock.
6. Use caution when installing or modifying
telephone lines.
15. Never push objects of any kind into this
product through cabinet slots as they
may touch dangerous voltage points or
short out parts that could result in a risk
of fire or electric shock. Never spill liquid
of any kind on the product.
7. Do not affix the AC power supply cord to
building surfaces with metal fittings (if
the product has an AC power cord).
8. Unplug this product from the wall outlet
before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
16. To reduce the risk of electric shock, do
not disassemble this product. Take it to
a qualified serviceman when service or
repair work is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause electric
shock when the product is subsequently
used.
9. Do not use this product near water, for
example, near a bathtub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool.
10. Do not place this product on an unstable
cart, stand, or table. The product may
fall, causing serious damage to the
product.
17. Unplug this product from the wall outlet
and refer servicing to qualified services
personnel under the following
conditions:
11. Slots and openings in the telephone’s
cabinet and the back or bottom are
provided for ventilation. To protect the
telephone from overheating, these
openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed,
sofa, rug, or other similar surface. This
product should never be placed near or
over a radiator or heat register. This
product should not be placed in a built-in
installation unless proper ventilation is
provided.
• When the power cord plug is damaged
or frayed.
• If liquid has been spilled into the
product.
• If the product has been exposed to rain
or water.
• If the product does not operate normally
by following the operating instructions,
adjust only those controls that are
covered by the operating instructions
because improper adjustments of other
controls may result in damage and will
often require extensive work by a
12. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure
of the type of power supply to your
3
Important Information
qualified technician to restore the
product to normal operation.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction
manual provided for this product.
• If the product has been dropped or the
cabinet has been damaged.
• If the product exhibits a distinct change
in performance.
6. Observe proper polarity orientation
between the battery pack and battery
charger.
18. Avoid using a telephone (other than a
cordless type) during an electrical storm.
There may be a remote risk of electric
shock from lightning.
SAVE THESE
INSTRUCTIONS
19. Do not use the telephone to report a gas
leak while in the vicinity of the leak.
BATTERY SAFETY
INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
FIRE OR INJURY, READ AND FOLLOW
THESE INSTRUCTIONS.
1. Use only the appropriate type and size
battery pack specified in the instruction
manual provided for this product.
2. Do not dispose of the battery pack in a
fire. The cell may explode. Check with
local codes for possible special disposal
instructions.
3. Do not open or mutilate the battery
pack. Released electrolyte is corrosive
and may cause damage to the eyes or
skin. It may be toxic if swallowed.
4. Exercise care in handing the battery
pack in order not to short it with
conducting materials such as rings,
bracelets and keys. The battery or
conductor may overheat and cause
burns.
4
Important Information
ˆ Contents
Introduction ............................................................................................................................ 6
Installation .............................................................................................................................. 7
Mounting the Phone ......................................................................................................... 7
On a Desk Top .......................................................................................................... 7
On a Wall Plate or Wall ............................................................................................. 8
Connecting, Charging, and Replacing the Battery Pack .................................................. 8
Setting the Dialing Mode ................................................................................................ 10
Setting the Handset Ringer’s Tone and Volume ............................................................. 10
Turning the Base’s Ringer On/Off ................................................................................... 10
Telephone Operation ........................................................................................................... 11
Making and Receiving Calls ............................................................................................ 11
Selecting the Channel ..................................................................................................... 11
Setting the Handset Volume ............................................................................................ 11
Using Flash ...................................................................................................................... 11
Using Redial .................................................................................................................... 11
Using Tone Services on a Pulse Line .............................................................................. 11
Paging ............................................................................................................................ 12
Memory Dialing ............................................................................................................... 12
Storing a Number in Memory .................................................................................. 12
Entering a Pause ..................................................................................................... 12
Dialing a Memory Number ....................................................................................... 12
Chain-Dialing Service Numbers .............................................................................. 13
Testing Stored Emergency Numbers ....................................................................... 13
Using a Headset ............................................................................................................. 13
Answering System Operation ............................................................................................. 14
Using the Menu Button ................................................................................................... 14
Setting the Day and Time ............................................................................................... 14
Setting the Number of Rings .......................................................................................... 15
Setting the Record Time ................................................................................................. 15
Selecting the Outgoing Message .................................................................................... 15
Recording/Deleting an Outgoing Message ..................................................................... 16
Setting the System to Answer Calls ............................................................................... 16
Screening Calls .............................................................................................................. 16
Recording Incoming Messages ...................................................................................... 16
Recording a Memo ......................................................................................................... 17
Recording a Conversation .............................................................................................. 17
Playing Messages .......................................................................................................... 17
Adjusting the Answering System’s Volume .................................................................... 18
Deleting Messages ......................................................................................................... 18
Remote Operation .......................................................................................................... 18
Setting the Security Code ....................................................................................... 18
Using the Toll-Saver ................................................................................................ 19
Using Remote Commands ............................................................................................. 19
5
Contents
Remote Commands ................................................................................................. 19
Troubleshooting ................................................................................................................... 20
Care ................................................................................................................................ 21
ˆ Introduction
Thank you for purchasing the RadioShack
900 MHz Cordless Telephone. Your system
combines a 900 MHz cordless telephone and
a digital answering system. The 900 MHz
band provides less interference, clearer
sound, and greater range than 46/49 MHz
cordless telephones.
You can also manually change channels
during a call.
Ringer Volume Control
— select from four
ringer tone/volume settings on the handset.
Volume Control
— adjust the sound level
you hear through the handset.
The digital answering system stores up to 16
minutes of messages on a computer chip
and records each message’s day and time.
Advantages over tape-based answering
machines include:
Long Battery Life
pack (when fully charged) provides about 7
hours of talk time or 14 days of standby time.
— the supplied battery
Security Access-Protection Code
— helps
prevent other cordless phone users from
using your phone line.
• Ability to delete individual messages
and save the rest.
• No tapes to bother with and no tape
mechanisms to wear out.
ANSWERING SYSTEM
Voice-Prompted Menu Setting
— set the
• Remote operation from a touch-tone
phone (or from a rotary phone with a
pocket tone dialer).
answering system’s various functions
through the voice guidance.
Two Prerecorded Messages
— offers the
option of using one of two prerecorded
messages (one that lets callers leave a
message and the other for the
announcement only setting) or recording
your own.
TELEPHONE
10 Number Memory Dialing
numbers (3 one-touch and 7 speed-dial) in
memory for easy dialing.
— store 10
Message Counter
recorded messages.
— shows the number of
Page
— send a paging signal from the base
to the handset to page someone or locate
the handset if you misplace it.
Programmable Security Code
— uses a
two-digit security code for secure remote
operation.
Headset Jack
headset (available at your local RadioShack
store) for hands-free convenience.
— connect an optional
Memo Recording
— lets you leave
messages for yourself or others in your
home or office. You can also record your
phone conversation.
40 Channels
channel when you make or answer a call.
— automatically selects a clear
6
Introduction
Phone Pick-Up Detection
Toll-Saver
— lets you avoid unnecessary
— stops
recording when you pick up any phone on
the same line as the answering system, and
resets to answer the next call.
charges when you call by long distance to
check your messages.
ˆ Installation
adapter from AC power before you
disconnect it from the phone.
MOUNTING THE PHONE
You can place the phone’s base on a desk or
table, mount it on a standard wall plate, or
directly on a wall. Choose a location that is:
Your telephone connects directly to a
modular telephone line jack. If your
telephone wiring does not have a modular
jack, you can update the wiring yourself
using jacks and adapters (available at your
local RadioShack store), or have the
telephone company update the wiring for
you. You must use compatible modular jacks
that are compliant with Part 68 of FCC Rules.
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
Note:
The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall plate
jack).
• away from other cordless phones
On a Desk Top
The base’s location affects the phone’s
range. If you have a choice of several
locations, try each to see which provides the
best performance.
1. Plug one end of the supplied long
TEL LINE
modular cord into the
the back of the base.
jack on
2. Plug the modular cord’s other end into a
modular telephone line jack.
Cautions:
You must use a Class 2 power
3. Insert the supplied AC adapter’s barrel
source that supplies 9V DC
and delivers at least 350 mA.
Its center tip must be set to positive and
!
DC IN 9V
plug into the
the base.
jack on the back of
DC IN 9V
its plug must fit the phone's
4. Route the adapter’s cord through the
strain relief slot on the bottom of the
base.
jack. The supplied adapter meets these
specifications. Using an adapter that
does not meet these specifications
could damage the phone or the adapter.
5. Plug the adapter into a standard AC
outlet.
• Always connect the AC adapter to the
phone before you connect it to AC
power. When you finish, disconnect the
6. Lift the base’s antenna to a vertical
position.
7
Installation
Note:
To mount the phone directly on a wall,
On a Wall Plate or Wall
you need two screws (not supplied) with
heads that fit into the keyhole slots on the
bracket. Follow the steps under “On a Wall
Plate or Wall,” then apply these additional
instructions for placement on a wall.
1. Insert the two tabs at the top of the
narrow end of the supplied bracket into
the base’s upper tab slots, then press
down on the bracket’s latches and insert
them into the lower slots.
1. Drill two holes 315/16 inches (100 mm)
apart. Then thread a screw into each
hole, letting the heads extend about 1/8
inch (3 mm) from the wall.
2. Plug one end of the supplied long
TEL LINE
modular cord into the
the back of the base.
jack at
3. Align the bracket’s keyhole slots with the
mounting screws and slide the base
downward to secure it.
2. Plug one end of the supplied short
TEL LINE
modular cord into the
the back of the base.
jack on
3. Insert the supplied AC adapter’s barrel
DC IN 9V
plug into the
jack.
4. Route the adapter and modular cords
through the grooves on the bracket.
5. Plug the modular cord’s other end into
the wall plate jack, then align the
bracket’s keyhole slots with the wall
plate studs and slide the base
downward to secure it.
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack installed in the
handset, but not connected. Before using
your phone, you must connect the battery
pack, then charge it for about 24 hours.
1. Press down and slide off the battery
pack compartment cover.
6. Plug the adapter into a standard AC
outlet.
2. Lift the battery
pack out of the
7. Press and lift out the handset holder, flip
it over, then snap it back into place so it
holds the handset.
compartment.
Plug the battery
pack’s
connector into
the socket in the compartment. The
connector fits only one way.
8. Lift the base’s antenna to a vertical
position.
8
Installation
3. Put the battery pack in the compartment.
4. Replace the cover.
while the handset is away from it, place
the handset on the base to reset the
security access-protection code. If the
handset lost power, recharge the battery
pack.
To charge the battery pack, simply place the
handset on the base, facing either up or
down. The CHARGE/IN USE indicator on the
base lights.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after an
overnight charge, replace it with a new 3.6-
volt, 600 mAh battery pack with a connector
that fits the socket in the battery
compartment. You can order a replacement
battery pack through your local RadioShack
store. Install the new battery pack and
charge it for about 24 hours.
Recharge the battery pack when the TALK/
BATT indicator on the handset flashes.
Important:
Be sure the battery pack is
properly connected before you try to charge
it. The CHARGE/IN USE indicator lights
when the handset is on the base even if the
battery pack is not properly connected.
Warning:
Dispose of the old battery pack
Notes:
promptly and properly. Do not burn or bury it
(see “Battery Safety Instructions” on Page 4
for additional information on proper battery
handling).
• When you first use the phone after
charging or recharging the battery pack,
the phone might not work and you might
hear an error signal. If this happens,
return the handset to the base for about
5 seconds to reset the security access-
protection code.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack for assistance.
Important:
The EPA certified
• Using a pencil eraser, clean the
charging contacts on the handset and
the base about once a month.
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
• If the phone does not work, recharge the
battery pack. (The battery power might
be too low to flash the TALK/BATT
indicator.)
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a
convenient alternative to placing used Ni-Cd
batteries into the trash or the municipal
waste stream, which may be illegal in your
area. Please call 1-800-THE-SHACK (1-
800-843-7422) for information on Ni-Cd
battery recycling and disposal bans/
restrictions in your area. RadioShack’s
involvement in this program is part of the
company’s commitment to preserving our
environment and conserving our natural
resources.
• If the battery pack becomes weak during
a call, the handset beeps. When this
happens, you cannot make a call until
you recharge the battery pack.
• About once a month, fully discharge the
battery pack by keeping the handset off
the base until the TALK/BATT indicator
flashes. Otherwise, the battery pack
loses its ability to fully recharge.
• If the battery pack is completely
discharged or the base loses power
9
Installation
SETTING THE DIALING
MODE
TURNING THE BASE’S
RINGER ON/OFF
Your phone is set for tone dialing. If you have
pulse service, you must change the dialing
mode. If you are not sure which type of
service you have, do this test.
You can set the base’s ringer to high or low,
or turn it off.
MENU
Press
four times. The phone
announces “Ringer volume” followed by its
current setting. The display also shows the
current setting.
TALK
Lift the handset, press
, and listen for a
0
dial tone. Press any number other than . If
your phone system requires that you dial an
SET
1. Press
to enter the setting mode.
9
access code ( , for example) before you dial
an outside number, do not press the access
code either.
Note:
when you:
The system exits the setting mode
If the dial tone stops, you have touch-tone
service. If the dial tone continues, you have
pulse service.
• wait more than 20 seconds between
key presses
• receive an incoming call
TALK
To set the dial mode, press
to hang up
the phone if necessary, then hold down
PLAY/STOP
• press
• press
FLASH
#
until the phone beeps. Then press
TONE
to set tone
mode. The phone beeps.
to set pulse mode or
/
∗
TALK
on the handset
Start again at Step 1.
Notes:
SKIP/
/REPEAT
to change
2. Press
; or :
• The phone exits setting mode if a call or
the setting. The system announces the
setting and the display shows >_, Be, or
E<.
TALK
page is received, or if you press
.
• If the battery pack power gets too low,
the dial mode might reset to tone. If you
are on a pulse line and cannot make a
call, try setting the dialing mode to
pulse.
SET
3. Press
to store the setting.
PLAY/STOP
4. Press
to exit the menu
setting mode.
Even when you turn off the base’s ringer, you
can still make or receive calls using this
phone. Telephones on the same line (and
the handset if it is away from the base) still
ring when there is an incoming call.
SETTING THE HANDSET
RINGER’S TONE AND
VOLUME
You can select one of four different ringer
tone/volume settings on the handset. At any
time except during a call, repeatedly press
VOLUME
to select the desired ringer setting.
Each time you press the button, the phone
rings at the selected setting.
10
Installation
ˆ Telephone Operation
MAKING AND RECEIVING
CALLS
USING FLASH
FLASH
performs the electronic equivalent of
a switchhook operation for special services,
such as Call Waiting.
To make a call, lift the handset then press
TALK
. The TALK/BATT indicator on the
handset and CHARGE/IN USE indicator on
the base light. Dial the number.
For example, if you have Call Waiting, press
FLASH
to answer an incoming call without
FLASH
disconnecting the current call. Press
again to return to the first call.
To answer a call, simply lift the handset from
the base. If the handset is away from the
base, press any key.
If you do not have any special phone
FLASH
services, pressing
the current call.
might disconnect
To end a call, place the handset on the base
TALK
or press
.
USING REDIAL
SELECTING THE CHANNEL
To quickly dial the last number dialed, lift the
The phone scans 40 channels (frequency
pairs used between the base and the
handset) and automatically selects a clear
channel each time you make or receive a
call.
REDIAL
handset and press
.
Notes:
• The redial memory holds up to 32 digits,
so you can redial long-distance as well
as local numbers.
If you hear other conversations or excessive
CH
noise during a call, press
to select a
different channel. The TALK/BATT indicator
blinks, and the handset beeps, followed by a
brief pause as your phone searches for a
clear channel.
• The redial memory also holds pause
entries (see “Entering a Pause” on
Page 12).
If the handset is too far from the base, the
channel might not change. Move closer to
the base and try again.
USING TONE SERVICES ON
A PULSE LINE
Some special services, such as bank-by-
phone, require tone signals. If you have
pulse service, you can still use these special
tone services. Dial the service’s main
SETTING THE HANDSET
VOLUME
number. When the service answers, press
/
∗
To change the volume you hear through the
TONE
. Any additional numbers you dial are
sent as tone signals.
VOLUME
handset, press
during a call. The
handset volume has three levels, low,
medium, and high.
When you hang up, the phone automatically
resets to pulse dialing.
11
Telephone Operation
than 20 seconds between each key
press.
PAGING
To page the person who has the handset or
to locate the handset when the phone is not
in use, press
• Each tone or pause entry uses one digit
of memory.
PAGE
on the base. The handset
beeps for 1 minute. To stop it from beeping
sooner, press any key on the handset or
• If you try to enter more than 16 digits,
the phone beeps and exits the
programming mode. Start over at Step 1
and enter no more than 16 digits in Step
2.
PAGE
return the handset to the base. Press
again to stop the paging at the base.
MEMORY DIALING
To replace a stored number, simply store a
new number in its place. To clear a stored
number, lift the handset (if the TALK/BATT
You can store up to 10 numbers in memory,
MEM
then dial a stored number by pressing
and a one-digit memory location number.
TALK
indicator lights, press
to turn it off) and
M1 M2
Also, with the press of one button (
,
, or
MEM
press
twice. Then press the memory
M3
), you can dial a number that is stored in
0 9
location number ( – ) you want to clear. The
one of the first three memory locations.
phone beeps.
Each number you store can be up to 16
digits long.
Entering a Pause
In some telephone systems, you must dial an
access code (9, for example) and wait for a
second dial tone before you can dial an
outside number. You can store the access
code with the phone number. However, you
must also store a pause after the access
code to allow the outside line time to
Use the supplied memory directory stickers
to record your stored numbers. Peel the
backing from each sticker and attach them to
the phone.
Storing a Number in Memory
PAUSE
connect. To do so, press
. Each press
MEM
1. Lift the handset and press
. The
enters a 2-second pause. For a longer
TALK/BATT indicator blinks.
PAUSE
pause, press
additional times.
2. Enter the number and any pause or tone
entries (see “Using Tone Services on a
Pulse Line” on Page 11 and “Entering a
Pause”).
Dialing a Memory Number
To dial a number stored in memory, lift the
TALK
handset or press
. The TALK/BATT
MEM
3. Press
again, then enter the
indicator lights. When you hear a dial tone,
0 9
memory location number ( – ) where
you want to store the number.
MEM
simply press
and enter the memory
location number for the number you want to
dial.
The phone beeps once to indicate that the
number is stored.
Or, to dial a number stored in the memory
M1 M2
M3
.
location 1, 2, or 3, just press
,
, or
Notes:
TALK
You need not press
these buttons.
when you use
• The phone beeps and exits the
programming mode if you wait more
Note:
If you select an empty memory
location. The phone beeps.
12
Telephone Operation
• With a headset connected, you make or
answer calls as usual using the keys on
the handset.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long distance or
bank by phone), store each group of
numbers in its own memory location. To use
the stored special service information, dial
the service’s main number first. Then, at the
• You can use an optional handset holder
(available from your local RadioShack
store) to hang the handset on your belt
for greater convenience.
MEM
appropriate place in the call, press
and
• When you finish using the headset,
disconnect it from the handset and close
the rubber cover to protect the jack.
0 9
enter the memory location number ( – ) for
the stored information.
Testing Stored
Emergency Numbers
If you store an emergency service’s number
(police department, fire department,
ambulance) and you choose to test the
stored number, make the test call during the
late evening or early morning hours to avoid
peak demand periods. Also, remain on the
line to explain the reason for your call.
USING A HEADSET
You can talk with hands-free convenience
using an optional headset that has a 3/32-inch
(2.5-mm) plug. Contact your local
RadioShack store for a suitable headset.
To connect the headset, open the rubber
cover on the side of the handset, then insert
the headset’s plug into the jack.
Notes:
• Connecting a headset disconnects the
handset’s earpiece and microphone.
VOLUME
•
on the handset also controls
the connected headset’s volume.
• If you place the handset on the base to
recharge it while the headset is
connected, be sure the handset seats
properly.
13
Telephone Operation
ˆ Answering System Operation
Note:
Enter each key press within about 2
USING THE MENU BUTTON
minutes. Otherwise, the system exits the
time setting process and you must begin
again with Step 1.
MENU
Use
on the base to select function
MENU
settings. Each time you press
, the
system announces the function and its
current setting.
MENU
1. Press
twice. The system
announces “Time”, then the currently set
time and the day of the week.
# of
Function
Presses
SET
2. Press
to enter the time setting
mode. The system announces the
currently set day and displays the day’s
number (& for Sunday, ' for Monday, and
so on).
1
2
3
4
5
Outgoing message
Clock set
Security code for remote operation
Ringer volume
SKIP/
3. Repeatedly press
; on the base
Number of rings before the system
answers
/REPEAT
to move forward or :
on the
base to move backward until the correct
6
Recording time for incoming
messages
SET
day appears, then press
. The
system announces and displays the
hour.
7
Exit the menu setting mode.
SKIP/
/
4. Repeatedly press
; or :
until the correct hour appears,
Note:
mode when you:
The system exits the menu setting
REPEAT
SET
then press
. The system announces
• wait more than 20 seconds between key
presses (except when you set the clock,
in which the time-out is about 2 minutes)
and displays the minutes.
SKIP
5. Repeatedly press
/; or :/
REPEAT
until the correct minutes
• receive an incoming call
SET
appear, then press
. The system
announces “AM” or “PM,” and 7 or F
appears.
PLAY/STOP
• press
• press
TALK
on the handset
SKIP
REPEAT
6. Press
AM or PM, then press
beeps and announces the day and time.
/; or :/
to choose
SET
. The system
Start again at Step 1 of the each section.
PLAY/STOP
7. Press
to exit.
SETTING THE DAY AND
TIME
MENU
To check the day and time, press
twice. The system announces the currently
You must set the day of the week and time
so the system can record the correct day and
time of each message.
PLAY/STOP
set day and time. Press
the menu.
to exit
14
Answering System Operation
Note:
SET
If power fails, the clock retains the
2. Press
.
current time. When the power is restored, it
starts counting again from the time the power
failed.
SKIP
3. Repeatedly press
/; or :/
REPEAT
until the desired number
appears.
SETTING THE NUMBER OF
RINGS
SET
4. Press
to store the setting.
PLAY/STOP
5. Press
to exit.
You can select how long the system waits to
answer a call — 2, 4, or 6 rings, or toll-saver.
If you plan to check messages by long
distance, set the ring time to toll-saver (see
“Using the Toll-Saver” on Page 19).
SELECTING THE OUTGOING
MESSAGE
The system has two prerecorded outgoing
messages. One asks the caller to leave a
message: “Hello, no one is available to take
your call. Please leave a message after the
tone.” The system uses this message when
the recording time is set to 1 or 4 (see
"Setting the Record Time").
MENU
1. Press
five times. The system
announces “Ring time” followed by the
current setting. The display also shows
the current setting (, *, ,, or jI (toll
saver).
SET
2. Press
.
The other is simply an announcement and
does not let the caller leave a message:
“Hello, no one is available to take your call.
Please call again.” The system uses this
message when the recording time is set to
Announce Only.
SKIP
3. Repeatedly press
/; or :/
REPEAT
until the desired number
appears.
SET
4. Press
to store the setting.
PLAY/STOP
5. Press
to exit.
You can also record your own message (see
“Recording/Deleting an Outgoing Message”).
When you record your own outgoing
message, the system uses it for all recording
time settings (1, 4, and Announce Only).
SETTING THE RECORD
TIME
You can set the recording time to 1, 4, or
Announce Only to determine how the system
will record incoming messages.
To switch between your outgoing message
and the system’s prerecorded message,
MENU
press
once to enter the outgoing
SKIP
message setting mode. Then press
/;
At the 1 or 4 settings, the system plays the
outgoing message and lets callers leave a
message up to 1 minute (or 4 minutes) long.
At the Announce Only setting, the system
plays the outgoing message but does not let
callers leave a message.
REPEAT
or :/
until the current message
starts to play. While the message is playing,
REPEAT
until the
desired message starts to play. The system
SKIP
press
/; or :/
switches to the other message and plays it.
MENU
1. Press
six times. The system
announces “Record time” followed by
the current setting. The display also
shows the current setting, ', *, or 7
(Announce Only).
15
Answering System Operation
When the system’s message memory is full,
<B appears and the system announces “No
remaining time” when you try to operate it.
RECORDING/DELETING AN
OUTGOING MESSAGE
Follow these steps to record your own
outgoing message (less then 30 seconds in
length).
SCREENING CALLS
You can let the system answer calls for you
while you listen to the caller’s message
through the base’s speaker. If you decide to
MENU
1. Press
once. The system
announces “Greeting message”,
followed by the current outgoing
message. #ý# appears.
TALK
answer the call, press
to answer if the
handset is off the base, or if the handset is
on the base, lift it.
MEMO/REC
2. Press
. The system
announces “Record your greeting after
the tone.”
You can also pick up any phone on the same
line. The system stops recording and resets
to answer the next call.
3. When the tone sounds, speak your
message.
VOLUME
Press
8 or 9 to adjust the volume
level of call screening. If you do not want to
4. When you finish your message, press
VOLUME
listen to calls, repeatedly press
9
MEMO/REC
PLAY/STOP
. The system
or
until & appears.
beeps and then plays back your
message.
The system silences at the 0 volume setting
only while screening calls. You can hear
message playback or other announcements
even at the 0 level setting.
PLAY/STOP
5. Press
to exit.
To delete your outgoing message and use
the system’s prerecorded messages, press
RECORDING INCOMING
MESSAGES
MENU
DELETE
when your
once, then press
message starts to play. The system
announces “Your greeting has been
deleted.”
After the system answers a call, it plays the
outgoing message, beeps, then records the
caller’s message. Each incoming message
can be up to 1 or 4 minutes long, depending
on how you set the recording time (see
“Setting the Record Time” on Page 15). The
system’s maximum recording capacity is
about 16 minutes (or approximately 59
messages).
SETTING THE SYSTEM TO
ANSWER CALLS
To set the system to answer calls, press
ANSWER ON/OFF
. If the system is set to
record a caller’s message (see “Setting the
Record Time” on Page 15), it plays the
outgoing message and shows the number of
recorded messages. If the system is set to
Announcement Only, it plays the outgoing
message, and 7 appears.
The system stops recording and resets to
answer the next call when:
• The caller hangs up.
To set the system to not answer calls, press
• The maximum message length is
reached.
ANSWER ON/OFF
again. The system
announces “Answer off” and the message
counter turns off.
16
Answering System Operation
• The system detects a busy signal or
more than 7 seconds of silence.
RECORDING A
CONVERSATION
• You pick up the system’s handset or any
phone on the same phone line.
The answering system lets you record both
sides of a telephone conversation when you
are talking with the handset.
Note:
When the system's message memory
is full, the caller will hear the prerecorded
announcement-only message ("Hello, no
one is available to take your call. Please call
again.") and the system cannot record
additional messages until you delete some of
the old messages (see “Deleting Messages”
on Page 18).
Important:
Every state has different
regulations governing the recording of
conversations over the telephone. Be sure to
check your local, state and federal laws
before using this product to record any
telephone conversation in order to determine
that your use is in compliance with such laws
or guidelines.
RECORDING A MEMO
To start recording a phone conversation,
MEMO/REC
on the base until the
A memo is a message you can record on the
system for yourself or others. The system
stores memos as incoming messages (see
“Playing Messages”).
press
answering system beeps and ## appears. As
it records the conversation, the system
beeps every 15 seconds to let the caller
know that the conversation is being
MEMO/REC
1. Hold down
until the system
PLAY/
recorded. To stop recording, press
beeps. The system announces “Record
your message after the tone.”
STOP
MEMO/REC
. The system stores a
or
recorded conversation as a message (see
“Playing Messages”).
2. When the tone sounds, speak your
message.
Notes:
3. When you finish the memo, press
• The maximum length for recording a
conversation is about 10 minutes.
MEMO/REC
PLAY/STOP
or
.
Notes:
• The system cannot record a
conversation less than 2 seconds long.
• The maximum length for recording a
memo is about 10 minutes.
• When the system’s message memory is
full, <B appears.
• The system cannot record a memo less
than 2 seconds long.
PLAYING MESSAGES
• When the system’s message memory is
full, <B appears and the system
announces “No remaining time” when
you try to operate it.
After the answering system has recorded a
message, its message counter flashes
showing the number of new messages. To
PLAY/STOP
play your messages, press
. The
system announces the number of new and
old messages, then plays the new
messages. The message number appears
as each message plays, and the system
17
Answering System Operation
announces the day and time of the call at the
end of each message.
“Messages have been deleted.” & appears in
the message counter window.
Note:
To play all messages after playing the new
You cannot delete new (unplayed)
PLAY/STOP
messages, press
again.
messages. If you try to delete all messages
while you still have new messages, the
system beeps and announces “Please play
back all messages.”
SKIP
To skip to the next message, press
while the message is playing. Hold down
/;
SKIP
/; to fast forward through the
SKIP
messages. Release
normal playback.
/; to resume
REMOTE OPERATION
While you are away from your home or
office, you can use a touch-tone phone, or a
pulse (rotary) phone with a pocket tone dialer
(available through your local RadioShack
store), to enter your security code and do
any of the following:
To replay the current message from the
REPEAT
beginning, press :/
. Hold down :/
REPEAT
to review the current message. The
system skips back every other second of
playback and plays the previous second,
until the beginning of the message. Release
REPEAT
:/
to resume normal playback.
• Set the system to answer or not answer
calls.
REPEAT
If you press :/
within about 2
seconds (4 seconds during remote
• Listen to your messages.
• Record a new outgoing message.
• Record a memo.
operation) after a message begins playing,
the system replays the previous message. If
the current message is the first new
message, the system plays back from the
beginning of the current message (it does
not go back into the old message group).
• Erase messages.
You cannot remotely operate the system
using its handset or another telephone on
the same line as the system.
ADJUSTING THE
ANSWERING SYSTEM’S
VOLUME
Setting the Security Code
To adjust the speaker’s volume, repeatedly
VOLUME
press
8 or 9 on the base. The
The system’s two-digit remote operation
security code prevents unauthorized remote
access to your messages. The code is
preset to 80.
volume setting from & (lowest) to / (highest)
appears in the message counter window.
DELETING MESSAGES
Follow these steps to change the code to any
number from 00 to 99.
To delete the current message while it is
DELETE
playing, press
system beeps.
. The answering
MENU
1. Press
three times. The system
announces “Security code,” followed by
the currently set code. The display also
shows the code.
To delete all messages, while messages are
not playing, hold down
DELETE
on the base
until the system beeps and announces
SET
2. Press
.
18
Answering System Operation
SKIP
3. Repeatedly press or hold down
/;
message, press pound two. For help,
press pound zero.”
REPEAT
or :/
to change the number.
SET
4. Press
to store the setting. The
If the system does not respond, try
entering your code again. If you enter an
incorrect code three times, the system
beeps and hangs up.
system announces the newly set code.
PLAY/STOP
5. Press
.
MENU
To check your code at any time, press
three times. The code appears in the
3. While the system is beeping, press #
and (within 2 seconds) the number for
the remote command you want.
message counter window, and the system
announces it.
Remote Commands
Using the Toll-Saver
Press #
To
If the ring time is set to jI (toll-saver) (see
“Setting the Number of Rings” on Page 15),
the system answers after two rings if you
have new messages (ones you have not
listened to). If there are no new messages,
the system answers after four rings so you
can hang up before the system answers and
avoid unnecessary long-distance charges. If
the system's message memory is full, the
system answers after about 10 rings
then
1
Repeat current message during
playback. If you press #1 within about
4 seconds after a message begins,
the system replays the previous
message (unless the message is the
first new message).
2
Play messages. The remote playback
of incoming messages is limited to 4
minutes. If you have more messages
after 4 minutes have passed, you
must press #2 again to listen to the
rest of the messages.
regardless of the ring time setting.
USING REMOTE
COMMANDS
3
4
Skip current message during
playback.
Follow these steps to operate the answering
system from a remote location.
Delete current message during
playback. You can only delete the
current message during playback.
You cannot delete all the messages
stored at one time.
Note:
If you wait more than 15 seconds
between each keypress, the system beeps
and hangs up.
5
6
Stop playback or recording.
1. Dial your phone number and wait for the
system to answer. If the system is not
set to answer calls, it will answer after
about 10 rings and beep.
Set the system to answer calls. The
system announces the current
outgoing message.
7
Record a memo. The system
announces “Record your message
after the tone.” The length of a memo
recorded by remote operation must
be over 2 seconds and within 4
minutes. Press #7 again or #5 to stop
recording.
2. When the outgoing message begins (or
the system beeps), press #, then enter
your security code within 2 seconds.
If the code is correct, the system
announces the number of new and old
messages, then “To play incoming
19
Answering System Operation
• When the system is in remote operation,
it stops all answering functions and the
display on the base shows h9. The
system resumes answering functions
when it is no longer in remote command
if you have not turned it off.
Press #
then
To
8
Record a new outgoing message. The
system announces “Record your
greeting after the tone.” Press #8
again or #5 to stop recording.
• The remote operation stops when
someone picks up the handset or any
phone on the same phone line.
9
0
Sets the system not to answer calls.
Announces the help guidance.
Notes:
ˆ Troubleshooting
We do not expect you to have any problems with your phone, but if you do, these suggestions
might help.
Problem
Suggestion
Low volume or unusual sounds
Someone has picked up another phone on the same line;
hang up the other phone.
CH
to change the channel.
Severe noise interference
Press
Keep the handset away from computers, remote control
toys, wireless microphones, alarm systems, intercoms,
room monitors, fluorescent lights, and electrical
appliances.
Move the handset to another location or turn off the
source of interference.
The phone cannot be operated at a useful
distance from the base because the signal
becomes weak or noisy (handset’s range
has decreased).
Lift the base’s antenna to a vertical position.
Return the handset to the cradle and recharge the battery
pack. Replace the battery pack if necessary. (See
“Connecting, Charging, and Replacing the Battery Pack”
on Page 8).
The phone does not work or works poorly.
The handset battery pack does not charge.
Be sure the base’s phone line cord and AC adapter are
correctly and securely connected, and the battery pack is
charged.
Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Replace the battery pack.
20
Troubleshooting
Problem
Suggestion
The handset does not ring or receive a
page.
Move the base away from other electrical devices and
sources of noise.
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack is charged. (If the battery power
is too low, it does not have enough power to light the
TALK/BATT indicator. See “Connecting, Charging, and
Replacing the Battery Pack” on Page 8.)
The handset stops working or works poorly
during a call.
Move the handset closer to the base.
Lift the base’s antenna to a vertical position.
Be sure the battery pack is charged. (If the battery power
is too low, it does not have enough power to light the
TALK/BATT indicator.) If the base loses power while the
handset is away, the security access-protection code
might change. Restore power to the base, then place the
handset back on the base. The CHARGE/IN USE
indicator lights, indicating that the code is set again.
Check the charging contacts on the handset and base. If
they are dirty, clean them with a pencil eraser.
The answering system does not answer
calls.
Make sure the system is turned on.
Make sure the AC adapter is properly connected.
Check all phone line connections.
The answering system does not record
callers’ messages.
The recording time is set to announcement only. Set it to 1
or 4.
Delete messages if memory is full.
If you still have problems, disconnect the phone. If other phones on the same line work
properly, the fault is in this phone or its installation. If you cannot find the problem, take your
phone to your local RadioShack store for assistance.
it. If your phone is not performing as it
should, take it to your local RadioShack store
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environments. Handle
the phone carefully; do not drop it. Keep the
phone away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
for assistance. If the trouble is affecting the
telephone lines, the phone company can ask
you to disconnect your phone until you have
resolved the problem.
Modifying or tampering with the phone’s
internal components can cause a
malfunction and might invalidate its warranty
and void your FCC authorization to operate
21
Troubleshooting
• connecting your phone to an AC outlet
that is on a different electrical circuit
from the receiver
FCC STATEMENT
Your telephone complies with Part 68 of the
FCC Rules. Upon request, you must provide
the phone’s FCC registration number and
REN to your telephone company. These
numbers are on the bottom of the base.
• contacting your local RadioShack store
for help
If you cannot eliminate the interference, the
FCC requires that you stop using your
phone.
Note: You must not connect your telephone
to:
Some cordless telephones operate on
frequencies that might cause interference to
nearby TVs and VCRs. To minimize or
prevent such interference, the base of the
cordless telephone should not be placed
near or on top of a TV or VCR.
• coin-operated systems
• party-line systems
• most electronic key phone systems
THE FCC WANTS YOU TO
KNOW
LIGHTNING
In the unlikely event that your phone causes
problems on the phone line, the phone
company can temporarily discontinue your
service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Your telephone has built-in protection circuits
to reduce the risk of damage from surges in
telephone line and power line current. These
protection circuits meet or exceed the FCC
requirements. However, lightning striking the
telephone or power lines can damage your
telephone.
Lightning damage is not common.
Nevertheless, if you live in an area that has
severe electrical storms, we suggest that you
unplug your phone when storms approach to
reduce the possibility of damage.
Also, the phone company can make changes
to its lines, equipment, operations, or
procedures that could affect the operation of
this telephone. The telephone company
notifies you of these changes in advance, so
you can take the necessary steps to prevent
interruption of your telephone service.
Your phone might cause TV or radio
interference even when it is operating
properly. To determine whether your phone
is causing the interference, turn off your
phone. If the interference goes away, your
phone is causing it. Try to eliminate the
interference by:
• moving your phone away from the
receiver
22
Troubleshooting
ˆ Notes
23
Notes
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
43-3812/3813
UCZZ01347ZZ
11A01
Printed in China
RadioShack Corporation
Fort Worth, Texas 76102
|