[ Quick Start Guide ]
INTELLIGENT STORAGE ROUTER INSTALLATION
z
i S R 6 1 5 2
Quick Start Guide
The iSR6152 is an intelligent Storage RouterTM that provides remote and local SAN island connectivity. The major
applications are:
■
■
Remote data replications between Fibre Channel storage arrays.
Connecting remote Fibre Channel servers to local Fibre Channel storage.
Suggested Configurations
Figure 1 shows connecting Local Array 1 to Remote Array 2, and the server from a local SAN to storage from a remote
SAN.
LAN
LAN
WAN
Server
Server
FC
SAN
FC
SAN
FC
SAN
FC
SAN
iSR6152
iSR6152
Local Array 1
Remote Array 2
Figure 1. Connect Remote SAN Islands
Figure 2 shows Fibre Channel storage from one SAN to a Fibre Channel server on different SAN.
LAN
LAN
WAN
Server
Server
FC
SAN
FC
SAN
FC
SAN
iSR6152
iSR6152
Local Array 1
Remote Array 2
Figure 2. Connect Remote Devices to Fibre Channel SAN
3
Installation Instructions
This quick start guide provides procedures for installing and configuring your new QLogic iSR6152 Router.
■
■
■
■
■
■
■
Step 1. Verify the package contents.
Step 2. Complete the pre-installation checklist.
Step 3. Mount the router.
Step 4. Install the small form-factor pluggable (SFP) transceivers.
Step 5. Apply power to the iSR6152 Router.
Step 6. Download and Install SANsurfer Router Manager.
Step 7. Configure the iSR6152 management port IP address.
Step 1. Verify the Package Contents
The QLogic iSR6152 Router is shipped with the following items:
■
■
■
■
iSR6152 Router (1)
SFP transceivers (2)
Serial adapter (1)
AC power cord (1)
Optional equipment:
■
Shelf for rack mount
Step 2. Complete the Pre-installation Checklist
During the initial configuration process, the system prompts you to enter information for the router. Use the spaces
Table 1. Worksheet for Router
Symbolic Name of iSR6152
IP Address (if not using DHCP):
Management Port (MGMT)
Subnet Mask (if not using DHCP):
Gateway (if not using DHCP):
IP Address:
Gigabit Ethernet (GbE)
Port 1 (GE1)
Subnet Mask:
Gateway:
IP Address:
GbE Port 2 (GE2)
Subnet Mask:
Gateway:
4
Table 1. Worksheet for Router (Continued)
IP Address:
GbE Port 3 (GE3)
GbE Port 4 (GE4)
Subnet Mask:
Gateway:
IP Address:
Subnet Mask:
Gateway:
Step 3. Mount the Router
Place the router on a flat surface, mount it in a standard 19-inch Electronic Industries Association (EIA) rack, or mount
it on the optionally available shelf.
Step 4. Install the SFP Transceivers
An SFP transceiver is required for each of the router’s Fibre Channel ports that will be connected to a Fibre Channel
device or switch. The iSR6152 Router package contains two SFPs.
To install an SFP transceiver, insert the transceiver into the router port, and then press gently until it snaps in place. The
transceiver will fit only one way. If the transceiver does not install under gentle pressure, flip it over and try again.
Step 5. Apply Power to the Router
Figure 3 shows the location of the ports and LEDs on the iSR6152 Router.
Heartbeat LED Input Power LED System Fault LED
RS232 Fibre Channel Ports Management Port
Port
GbE Ports
AC Power
10/100 Ethernet
Figure 3. iSR6152 Ports and LEDs
1.
2.
Attach the AC power cord to the iSR6152 Router, and then to the wall outlet or power strip.
Verify that the router’s input power LED is illuminated.
The iSR6152 Router first runs its self-test, which takes about one minute, and then begins normal
operation.
3.
Verify that the heartbeat LED is blinking (once per second) and that the system fault LED is not
illuminated.
For installation details, diagnostics, and troubleshooting, see the iSR6152 Intelligent Storage Router Installation Guide.
5
Step 6. Download and Install SANsurfer Router Manager
Follow these steps to download the SANsurfer Router Manager utility from the QLogic Web site to a PC workstation and
then install it:
1.
2.
Close all programs currently running.
Go to the QLogic Downloads and Documentation page:
3.
4.
Under Downloads– QLogic Products, type iSR6152 in the search box.
In the search results, locate Management Tools, and then click the appropriate SANsurfer Router
Manager for your operating system type.
5.
Click the End User Software License Agreement link to read the EULA; close the window when you
are done.
6.
7.
8.
Click Download Now.
Save the installation file to your local machine.
Run the SANsurfer Router Manager installer by following the system prompts.
Step 7. Configure iSR6152 Management Port IP Address
Connect the router’s 10/100 Ethernet port to your workstation using a switch or hub. Alternatively, you may connect
your workstation directly to the router using an Ethernet crossover cable.
The iSR6152 management port’s default IP address is 10.0.0.1, subnet 255.0.0.0. Make sure the workstation connected
to the iSR6152 Router has Ethernet address 10.0.0.x, where x is an integer other than 1 and the subnet mask is 255.0.0.0.
To configure the management port IP address:
1.
2.
3.
From the workstation, open a command window.
Using a Telnet session, connect to the iSR6152 using IP address 10.0.0.1.
Login as guest, and enter the password, password, as shown:
iSR6152 login: guest
Password: ********
The command line interface (CLI) appears as shown:
Welcome to iSR6152
******************************************************
*
*
*
*
*
*
iSR6152
******************************************************
4.
5.
6.
At the iSR6152 #> prompt, issue the admin start command.
Enter the default password, config.
At the QRouter (admin) #> prompt, issue the set mgmt command.
The CLI responds as follows:
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current value.
If you wish to terminate this process before reaching the end of the list
6
press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to the MGMT port.
7.
At the CLI prompts, configure the router addresses as follows:
a.
b.
c.
d.
At the IPv4 Interface (0=Enable, 1=Disable)prompt, enter 0 to enable this
option.
At the IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) prompt, enter 0
to select the Static mode (recommended).
At the IPv4 Address, IPv4 Subnet Mask, and IPv4 Gateway prompts, enter
the IP addresses for these items.
At the IPv6 Gateway and IPv6 Interface prompts, press ENTER to accept the
current values.
The CLI responds as follows:
All attribute values that have been changed will now be saved.
iSR6152 (admin) #>
Because of the changes made to the management port, the router loses connectivity of the Telnet
session.
8.
9.
If you want to continue using the CLI, restart the Telnet session with the IP address you just assigned
to the management port.
You now have the management port configured with the appropriate IP address.
Connect the management port cable to your Ethernet network.
10. Connect cables to the GbE and Fibre Channel ports needed by your configuration (see the examples
Congratulations! You have now successfully installed your QLogic
iSR6152.
For optimal parameter settings, see “Performance Tuning” in the iSR6152 Intelligent Storage Router Installation Guide.
7
Warranty
The QLogic iSR6152 Router comes with a standard one-year QLogic warranty, or as specified by other agreements. For
Regulatory Information (Preliminary)
The following sections contain a summary of EMC/EMI test specifications performed on the QLogic iSR6152 Router to
comply with radiated emission, radiated immunity, and product safety standards.
Safety Standards
UL60950 (USA)
Voltage Fluctuations
EN61000-3-3
CSG 22.2 No. 60950 (Canada)
EN 60950 (EC)
Marking
FCC Part 15
UL (United States)
TUV (United States)
cUL (Canada)
cTUV (Canada)|
TUV Europe (Germany)
VCCI
CB Scheme-IEC 60950
Harmonics
EN 61000-3-2
Immunity
EN 55024:1998
CE
GOST
KCC (Class A)
BSMI/RRL
Emission Standards
FCC Part 15B Class A (USA)
VCCI Class A ITE (Japan)
ICES-03 Issue 3 (Canada)
EN55022 Level A (EC)
CISPR 22, Class A
KC (Korea) Class A
KCC Regulatory for iSR6152: KCC-REM-QLG-ISR6152
A class equipment
(Business purpose info/telecommunications
equipment)
As this equipment has undergone EMC registration for business
purpose, the seller and/or the buyer is asked to beware of this point
and in case a wrongful sale or purchase has been made, it is asked
that a change to household use be made.
A 급 기기 ( 업무용 정보통신기기 )
이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주
의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로 합니다 .
8
9
10
© 2011 QLogic Corporation. QLogic, the QLogic logo, intelligent Storage Router, and SANsurfer are trademarks or
registered trademarks of QLogic Corporation. All other brands and product names are trademarks or registered
trademarks of their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic
Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without
notice, to make changes in product design or specifications.
Corporate Headquarters
International Offices
QLogic Corporation
UK | Ireland | Germany | France
India | Japan | China
Hong Kong | Singapore | Taiwan
26650 Aliso Viejo Parkway
Aliso Viejo, CA 92656
949.389.6000 www.qlogic.com
*ISR654503-00 D*
ISR654503-00 D
|