PREPARATIONSꢀ
•ꢀꢀUseꢀtheꢀPYLEꢀPROꢀSpeakerꢀSelectorsꢀonlyꢀwithꢀamplifiersꢀratedꢀatꢀ100ꢀwattsꢀperꢀ
channelꢀorꢀless.
•ꢀꢀYourꢀPYLEꢀPROꢀSpeakerꢀSelectorꢀisꢀdesignedꢀtoꢀacceptꢀanyꢀsizeꢀcableꢀupꢀtoꢀ14ꢀgaugeꢀ
non-terminatedꢀspeakerꢀwire.ꢀIfꢀyou’reꢀusingꢀnon-terminatedꢀspeakerꢀwire,ꢀdoꢀnotꢀuseꢀ
anyꢀspeakerꢀwireꢀthatꢀisꢀlargerꢀthanꢀ14ꢀgauge.ꢀTheꢀlowerꢀtheꢀgaugeꢀnumber,ꢀtheꢀlargerꢀ
theꢀcableꢀ(e.g.,ꢀ12ꢀgaugeꢀisꢀlargerꢀinꢀactualꢀphysicalꢀsizeꢀthanꢀ14ꢀgauge).
•ꢀꢀDoꢀnotꢀhookꢀtheꢀoutputsꢀofꢀoneꢀselectorꢀintoꢀtheꢀinputsꢀofꢀanotherꢀspeakerꢀselectorꢀ
together.
MAKINGꢀTHEꢀCONNECTIONS
Theꢀcontrolꢀcenterꢀdividesꢀtheꢀpowerꢀfromꢀyourꢀreceiver/amplifierꢀdifferentlyꢀtoꢀitsꢀ
speakerꢀterminals.ꢀ(Thisꢀisꢀespeciallyꢀnoticeableꢀwhenꢀyouꢀconnectꢀonlyꢀoneꢀpairꢀofꢀ
speakers.ꢀIfꢀyouꢀconnectꢀmoreꢀthanꢀoneꢀpairꢀofꢀspeakers,ꢀseeꢀ“ImpedanceꢀChart”ꢀonꢀ
pageꢀ5ꢀtoꢀselectorꢀtheꢀbestꢀterminalsꢀtoꢀconnect.)ꢀForꢀtheꢀbestꢀperformance,ꢀmakeꢀtheꢀ
connectionsꢀbasedꢀonꢀhowꢀfrequentlyꢀyouꢀuseꢀeachꢀsetꢀofꢀspeakers.
Cautions:Toꢀavoidꢀdamagingꢀyourꢀspeakersꢀorꢀreceiver/amplifier:
•ꢀꢀBeꢀsureꢀyourꢀreceiver/amplifier’sꢀpowerꢀisꢀturnedꢀoffꢀbeforeꢀyouꢀmakeꢀtheꢀconnections.
•ꢀꢀNeverꢀletꢀtheꢀspeakerꢀwire’sꢀbareꢀendsꢀtouchꢀeachꢀotherꢀorꢀtheꢀadjacentꢀterminalsꢀonꢀtheꢀ
controlꢀcenter.
•ꢀꢀDoꢀnotꢀconnectꢀmoreꢀthanꢀoneꢀpairꢀofꢀsepakersꢀtoꢀeachꢀsetꢀofꢀterminals.
2
PressꢀopenꢀtheꢀdesiredꢀSPKꢀterminalsꢀonꢀtheꢀcontrolꢀcenter.ꢀInsertꢀtheꢀspeakers’ꢀpositiveꢀ
(+)ꢀwiresꢀinꢀtheꢀpositiveꢀ(red)ꢀterminals,ꢀandꢀnegativeꢀ( )ꢀwiresꢀintoꢀtheꢀnagativeꢀ(black)ꢀ
-
terminals,ꢀaccordingꢀtoꢀtheꢀrespectiveꢀLꢀ(left)ꢀandꢀRꢀ(right)ꢀterminals.ꢀThenꢀpressꢀtheꢀtabsꢀ
toꢀcloseꢀthem.
PressꢀopenꢀtheꢀAMPꢀterminalsꢀonꢀtheꢀcontrolꢀcenter,ꢀthenꢀinsertꢀyourꢀreceiver/amplifier’sꢀ
positiveꢀ(+)ꢀwiresꢀintoꢀtheꢀpositiveꢀ(red)ꢀterminals,ꢀandꢀnegativeꢀ(-)ꢀwiresꢀinꢀtheꢀnagativeꢀ
terminals.ꢀThenꢀpressꢀtheꢀtabsꢀtoꢀcloseꢀthem.
3
Notes:
•ꢀꢀIfꢀyourꢀreceiver/amplifierꢀhasꢀmoreꢀthanꢀoneꢀsetꢀofꢀspeakerꢀterminalꢀ(AꢀandꢀB),ꢀconnectꢀ
onlyꢀoneꢀorꢀtheꢀotherꢀtoꢀtheꢀcontrolꢀcenter.
•ꢀꢀForꢀtheꢀbestꢀresults,ꢀweꢀrecommendꢀ14-gauge,ꢀtwoꢀconductorꢀspeakerꢀwireꢀ(notꢀ
supplied)ꢀforꢀmostꢀconnections.ꢀIfꢀyouꢀplanꢀtoꢀlocatedꢀtheꢀspeakersꢀfurtherꢀthanꢀ80ꢀfeetꢀ
fromꢀtheꢀcontrolꢀcenter,ꢀuseꢀaꢀheavierꢀgaugeꢀofꢀwire.
OPERATION
Caution:Toꢀavoidꢀdamagingꢀyourꢀreceiver/amplifier,ꢀsetꢀitsꢀvolumeꢀtoꢀtheꢀlowestꢀsettingꢀ
beforeꢀchangingꢀtheꢀcontrolꢀcenter’sꢀsettings.
Toꢀturnꢀonꢀaꢀpairꢀofꢀspeakersꢀconnectedꢀtoꢀtheꢀcontrolꢀcenter,ꢀsimplyꢀpressꢀinꢀtheꢀdesiredꢀ
button.ꢀForꢀexample,ꢀtoꢀturnꢀonꢀtheꢀsetꢀofꢀspeakersꢀconnectedꢀtoꢀSPKꢀA,ꢀpressꢀA.
Toꢀturnꢀoffꢀaꢀpairꢀofꢀspeakers,ꢀpressꢀtheꢀbuttonꢀagainꢀsoꢀitꢀisꢀinꢀtheꢀ“out”ꢀposition.
Note:ifꢀnoꢀspeakersꢀareꢀconnectedꢀtoꢀaꢀsetꢀofꢀterminals,ꢀdoꢀnotꢀpressꢀinꢀtheꢀcorrespondingꢀ
controlꢀbutton.
4
IMPEDANCEꢀCHART
Impedanceꢀisꢀaꢀmeasurementꢀofꢀtheꢀloadꢀplacedꢀonꢀyourꢀreceiver/amplifierꢀbyꢀtheꢀ
speakers.ꢀTheꢀloadꢀplacedꢀonꢀyourꢀreceiver/amplifierꢀfromꢀthteꢀcontrolꢀcenterꢀwillꢀ
varyꢀdependingꢀonꢀhowꢀmanyꢀpairsꢀofꢀspeakersꢀyouꢀturnꢀonꢀatꢀoneꢀtime,ꢀandꢀonꢀwhichꢀ
speakersꢀyouꢀturnꢀon.ꢀTheꢀchartꢀbelowꢀshowsꢀtheꢀimpedanceꢀforꢀallꢀpossibleꢀcombinationsꢀ
ofꢀ8-ohmꢀspeakers.
PSS6
PSS4
Speaker Sets On Impedance (Ω)
Speaker Sets On
Impedance (Ω)
A, B, C, D, E or F
8
A, B, C or D
8
4
A+B, A+C, A+D
B+C, B+D, C+D
A+B, A+C, A+D
A+E, A+F, B+C
B+D, B+E, B+F
C+D, C+E, C+F, E+F
4
A+B+C, A+B+D
A+C+D, B+C+D
3.1
2.4
A+B+C+D
A+B+C, A+B+D, A+B+E
A+B+F, A+C+D, A+C+E
A+C+F, A+D+E, A+D+F
A+E+F, B+C+D, B+C+E
B+C+F, B+D+E, B+D+F
C+D+E, C+D+F, D+E+F
3.1
2.4
A+B+C+D, A+B+C+E
A+B+C+F, A+C+D+E
A+C+D+F, A+D+E+F
B+C+D+E, B+C+D+F
C+D+E+F
A+B+C+D+E+F
1.7
5
SPECIFICATIONS
AudioꢀPowerꢀHandlingꢀꢀ
ꢀ
50Wꢀ(R.M.S.)/ch,
100Wꢀ(Max)/ch
20ꢀHzꢀtoꢀ20KHz
80ꢀdB
FrequencyꢀResponseꢀ
ChannelꢀSeparationꢀ
Crosstalkꢀbetweenꢀchannelsꢀ
50ꢀdB
Speakerꢀterminalꢀwireꢀsizeꢀrequirementsꢀ 14-22ꢀawg
Dimensionsꢀ(WxHxD)ꢀꢀ
190x50x120ꢀmmꢀ(PSS4)
ꢀ
250x50x150ꢀmmꢀ(PSS6)
0.81kgsꢀ(1.79lbs)ꢀ(PSS4)ꢀ
1.15kgsꢀ(2.54lbs)ꢀ(PSS6)ꢀ
Weightꢀ
ꢀ
ꢀ
ꢀ
6
|